Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
I Have AP350 legacy model. Recently I lost power injector of AP350. So I'll order PWINJ3 soon. Is PWRINJ3 available with AP350?
Hello everybody.Can the two wireless client under the same AP1121G support the multicast forwarding?What do I config on the AP1121G?Thanks a lots.
Hi,I would like to know the procedure for recoering passwords on Cisco 2000/ 4000 series contorllers.Please Help!Thanks and Regards,Mohan
I want to upgrade the existing Layer 2 contollers 4100 and AP 1200 (in the same subnet) to Layer 3 (controller is different subnet from AP). Due to migration in phases, I need to have mix Layer 2 and Layer 3 controllers in short period of time. Any i...
OK so I am setting up a wireless network that is going to have about 500 AP’s on it. There are about 30 at each remote location. I want to use LEAP for authentication. If the WAN connection at a site goes down or worse the ACS server is dead, how can...
Hello,I generated a certificate on my ACS - how do I add it to my windows PC wireless client so I can use it for EAP-TLS. On my windows PC I found certificate import wizard but the types supported are for .P7B, .PFX, .P12 file type and I believe the...
Hello,I am able to authenticate with EAP-FAST auto provisioning but I am hesitant to use it due to MITM attacks. I generated a manual .pac file on the ACS for my userid and loaded it on the client no problem. But I am unable to authenticate - no e...
Resolved! AP 1310 setting 802.11b
Hi, the manual and the brochure of AP 1310 say that's possible to use the AP in 802.11b mode with 100 mW of maximum output power level but the the only working mode seems to be 802.11g @ 20 mW.Is it really possible to change? Does anybody know how t...
Has anyone used manual PAC provisioning with ACS 4.0 and Cisco ACU 2.6. I create a PAC in ACS using "csutil -t -u <username> -passwd <pwd> -filepath <filepath>". I get a PAC file but ACU returns message "Error importing the EAP-FAST PAC file.".Ran ...
Hello,i have some trouble with my wireless enviroment.The wireless enviroment consist of 30 cisco aironet 1210 access points, cisco wlse and cisco acs with ads authentification.Since the last ios upgrade to version 12.3.8 on the aironet access points...
Hi, I want that the users of the Corporation get access to the WLAN using the active directory? Is that possible? How can I accomplish this task. I'm working with an ACS and AP 1100 Any help will be appreciatedRegards
Hey,I am trying to get WDS configured and working, but for some reason it is not correctly authenticating to the IAS radius server. I followed the cisco document exactly (except configured IAS instead of ACS). I get the following when debugging radiu...
If a facility has perhaps 10 to 20 WAPs to provide wireless VOIP, is a Wireless LAN Controller required to handle the hand-off between WAPs as a user roams from one WAP to another?
Greetings,Here is what I would like to do.-On a mobile platform (RV), I want to be able to park within range of a wifi hotspot and to connect a router to the hotspot and to route traffic from my internal network over the wifi 'wan'. So, rather than c...
I'm trying to setup my wireless in a test environment before putting in my production just to verify I know how to set it up. Here is what I have: 3560 switch/POE, 4402 WLC, & a 1000 AP. I plugged my AP into f0/1 of my switch and added it to VLAN 3. ...
