Wireless

Hi,I have an interesting problem with an Intel 3945 A/G card, and my cisco APs.1. Given:Cisco 1100 and 1200 AP running IOS 12.3.8-JEATwo laptop, one with Intel 2200 MPCI Card, the other with Intel 3945 MPCI CardMicrosoft AD with IAS radius servera. 1...

Helloon the 3750 (WS-C3750G-48PS with 12.2(25)SEE2)Switch we have several different type of LWAPP accesspoint. In the cdp neighbor table in the switch are just the "old" airespace (1010/1020) ap with the right name visible, the 1131/1242 shows just "...

Hi,I have a Cisco Wireless Controller Model 4402 with 1131 Model APs. I am trying to get the APs to see the controller, but no success. I am using a Lucent QIP DHCP server (which I know very little about) and am thinking that I need to configure Opti...

dear gentlemen,i have one wlc-4402 controller and some clients. how to configure the netbios over tcp/ip in the controller, so that the clients can assiciate the network.thank?s in advance michael

Hi all,I followed the steps outlined in this guide:http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008070ba8f.shtml...of course I modified it a bit. And it all works, I am just a little confused at why it works if ...

I keep getting this message whenever I boot my WLC. I have the Date and Time set correctly but I'm not sure how to set the timezone. Timezone options are Delta: hours __ minutes__Daylight Savings Enable or disableThe message I keep getting is this:"C...

While auditing a client (using Kismet) I found that some of their Cisco APs have a <info> field in beacon packets. I'm trying to figure out where the data for this field is entered in the configuration. I do not have access to the configurations. The...

I have two SSIDs for two data networks. I want the users in one SSID have more bandwidth than other other. My original thought was put them into two differnt QoS profiles(Gold and Silver) and assign different Avg/Burst rates to the two QoS profiles. ...

We have a pair or 8600's that we have configured SMLT with the 4404's LAG option. Unicast network traffic is flowing and working correctly and the SMLT/LAG failover works without a problem. The MLT trunk has 3 tagged VLAN's and no untagged native vla...

Hi guysso i finished my intership of 1year and now i am back in university, and guess what my networks assignment is to make a report to a company that wants to set up a wireless network.anyway the office is supposedly a 200 X 200 mettersi got it all...

I'm setting up some access points for WPA. I've ran into a strange issue. The client VLAN (VLAN that the users will be put into) is 1, and the native VLAN is 10. The RADIUS server is in VLAN 1 (but I have a test RADIUS server in VLAN 10 as well). I c...

All,we have migrated from WLSM to WiSM (4.0.179.11). To enable IPv6 for the clients on the WLSM it was enough to give either the VLAN-if or the tunnel-if a valid IPv6 address and the attached clients had the possibility to retrieve an IPv6 address vi...

We are planning to install wireless AP Cisco 1200 in my organization (right now we have got only two APs) , what should I take in consideration we I do the design 1- Distance between APs2- If I used LEAP for authentication, do I need to configure an ...

Is it possible to configure web authentication with PEAP? If so, how would I go about doing so?

Hi, I have a 857 and I would like to setup as repeater of a toshiba wireless router.Could my 857 work as a repeater? What would be the difference beteween a device working as repater and a link with WDS?