Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

ok.. I'm looking at these solutions and I'm very puzzled why I would purchase a WLC/WCS/AP vs a WLSE/AP solution. First with WLC, i have to deploy multiple WLC's to get global redundancy. Don't need that with AP/WLSE combo. WLSE isn't a global failur...

rpaquin by • Level 1
  • 1397 Views
  • 1 replies
  • 0 Helpful votes

Cisco Aironet 1200 installed on testing network. My laptop is picking signals from 3 other access points, but not the 'TEST' one.Please find attached access point running-config. Can you help me and please advise why this SSID is not being visible ?I...

news2010a by • Level 7
  • 5751 Views
  • 2 replies
  • 0 Helpful votes

Hi Everyone,I'd like to solicit opinions regarding a wireless network that my company is planning to deploy using Cisco 1000 Access Points and 4402 Wireless LAN Controllers.Our network includes about 60 remotes sites connected to headquarters via sin...

IHCowan by • Level 1
  • 780 Views
  • 2 replies
  • 0 Helpful votes

HiIn my WCS, I see hundreds of rogue AP. Most of them are my AP also controled by my WiSMs. Wy does I get rogue report for them? The radio mac of the rogue report is usualy one digit higher then the base mac of the AP

Dear EveryoneI work for a company with about 300 wireless users and 15 access points installed.Currently I use LEAP authentication as security, which authorizes by username andpassword, and thereafter it checks if MAC address is recorded in access li...

narius210 by • Community Member
  • 999 Views
  • 2 replies
  • 0 Helpful votes

Hi, were setting up a wireless network for test purposes. Our question is will the Cisco 4400 series WLAN controller be able to act as a DHCP server to allocate IP information to trusted wireless devices? 2) Am I right in thinking that if the Cisco 1...

mbaylis by • Level 3
  • 660 Views
  • 1 replies
  • 0 Helpful votes

We have WPA2 clients and WLC4402, why is the controller reporting this error message. Does anyone know ? It doesn't seem to effect the connection but I'm just concerning.Tue May 9 12:47:20 2006 WEP Key decrypt error. Station MAC Address is xx:xx:xx:x...

t.han by • Community Member
  • 933 Views
  • 2 replies
  • 0 Helpful votes

1. Deauthenticating Station xxxx.xxxx.xxxx Reason: Sending station has left the BSSUnder what condition will the AP print this? I can image that if client send out Disassociation or Deauthentication, AP should print this. Is there any other reason ca...

atc by • Community Member
  • 571 Views
  • 1 replies
  • 0 Helpful votes

Hello,We have a few WLC's on our Network. The last WLC we deployed is having issues with connectivity. Persistent PING tests are showing drops every 20 packets or so. We noticed that the Mgt VLAN is flapping in STP.The WLC is connected to a 4506 Swit...

john.judge by • Community Member
  • 1213 Views
  • 5 replies
  • 0 Helpful votes

Hi,I want to install the Sup720 and the WiSM module, I know I have to create a VLAN that is used to communication between WiSM and Catalyst Sup720, then I have to create a DHCP Scope for the service port of the WiSM in the Sup720 and associate the VL...

landovalbo by • Community Member
  • 949 Views
  • 1 replies
  • 0 Helpful votes

I have made an IOS upgrade to an aironet 1100 AP, but we had a power loss and now the ap is not starting. i can't access it nor by the old ip i have linked an ip by hand with arp -s, but i can't access it. how can I revert to the old IOS or how can i...

gorea.adrian by • Community Member
  • 1303 Views
  • 2 replies
  • 0 Helpful votes

Good day Gentleman,Have someone a config example for a 878W (or Cisco DSL router with Wireless)with a ipsec tunnel to a pix.Thanks in advance

beumer by • Community Member
  • 708 Views
  • 2 replies
  • 0 Helpful votes
Review Cisco Networking for a $25 gift card