Wireless

My client has 5 AP350s, which have been installed and running for 2-3 years with no incident. Some 2 weeks ago they started getting drops from one AP in particular. We have moved a spare unit in place, replaced antennas (diversity 5.2 dbi omnis), m...

OK got a few questions. Please execuse me as I am not clued on to Wireless networks at all. 1) Is it possible to connect a Cisco Wireless Access Point to an A/DSL Broadband Internet connection? If so, what models would you recommend.2) Would say, (fo...

We got two new sites connected using 350 bridges. It is giving us problems with configuration not being saved. For e.g whenever we off encryption on both sites it will work ok for sometime and after that it will get disconnected. When we check the co...

Hello, I'm new here.We have a AP1100 set with wep 40bit, and nothing special, other then the defaults. The dhcp ip's, are not being re-issued, when we disconnect from the AP.Our network flows like thisT-1 --> 2610 router --> PIX515 The pix has two t...

I have a client whose internal Cisco 350 series card is associated to a 1200 series Cisco AP, and they receive a valid IP address. According to the AP, they have a valid IP address. But the AP shows many decrypt errors for the client. And the clie...

I purchased two WGB350 wireless bridges to connect a remote building to our plant LAN. However, I am not able to get these two bridges to associate. Does the one in the remote building need to be an access point instead? I've read for some models t...

Just upgraded my AP340 from 11.07 to 12.04 (Firmware from CCO) and now the AP 340 has an Aironet Picture instead of the Cisco picture in the Web based GUI.The other trouble is that now my WLSE (WLSE v2.5) can't discover anymore my AP ...I tried to do...

Hi experts !Does somebody knows how to configure ACS 3.2 Solution Engine appliance for communicate with a RSA Secur-ID Token-Server V5.After successfully activated PEAP on ACS 3.2 Solution Engine Appliance with a good certificate, clients cannot auhe...

I have got a WLAN consisting of 1220 ap's (IOS : 12.2) Im ok connecting with my origional cb20a-e cards but cant with my new cb21ag-e cards. It seems to have a link but no data will transfer. Any suggestions will be gratefully recieved.Thanks

Looking for anyone that has had a similiar experience. In our warehouse we have areas of coverage that get into the single digits of SNR. This has been acceptable with our telnet application. What we have noticed lately is, in the fringe areas, wh...

AP1220 running VxWorks. Purchased WLSE and need to use some of the great functions it has. It seems to me that we have to change from VxWorks to IOS so we can use WDS, control the radios, SWAN, measure radio coverage, do walk abouts, etc. Is my inter...

We have successfully piloted EAP-TLS with machine certificates for wireless using microsoft IAS and I am investigating converting to ACS for the radius piece. One thing I can't figure out how to do with ACS is to check policy settings for the suppli...

Hellowhich software for cisco wireless client has the option to feed radio measurments to the wlse?(cisco say something about carbon firmware...)any input is welcome

Hi,I just configured a WLSE for out 5 APs. All APa are 1200. Four of them with .g radio and one with .b radio.The WLSE identifies 3 of the 4 .g radios as .a with strange implications: In the location manager the correct channel in the 2.4GHz range ar...

I'm trying to get the number of clients associated to my 1200 APs which have dual A/G radios using SNMP. When I use the usual OID (the same one I use for my 1100 series APs) I get a constant 1 for the # of clients. I've tried many variations on thi...