Wireless

My scenario as follows:Cisco Aironet AP (non IOS-350 series & IOS-1200 series)ACS 3.2 appliance Active DirectoryHow can I authenticate the administrators for booth non-IOS & IOS AP by the ACS 3.2?Does non-IOS 350 series support RADIUS authentication?...

Hello, I have been using Vxworks v.12.02 running this exact configuration without any problems. Recently I have upgraded to IOS 12.2(13)JA2. My configuration is running diversity with antenna cable running into two seperate cells connected to 2.2 dBi...

does the 12000 support 2 active directories. I have acustomer in the hospitaland they have 2 segments one for the doctors and one for the hospital. The doctors wouldm like to access the network not ony from his desk, but would like to also access the...

Hi,I have a customer who has put 8 PC's AND a print server behind the WGB so now they are having problems. Just out of curiousity does anyone know what the ARP timeout would be on the WGB before the extra user could connect through it?

I seem to have noticed the following in reguard to the cb21ag.Slow scanning...tends to stick with bad ap and not roam to another/better AP.Not able to use the Cisco Conf utility for any authentication besides leap on XP. To use WPA/TKIP with PEAP or ...

The WAP only does 802.11b. I would like to be able to use 802.11a. How do I configure the WAP to do 802.11a? my current software version: 12.2(11)JA1Thanks.

Hello, need help on this one.We're using 1231G with 12.2(13)JA, WPA(PEAP) towards an ACS. Some clients work well but it seems like the 3Com 802.11G PCMCIA (WiFi and WPA-certified) associates as a repeater instead of a client. Have tried 3 cards of th...

I have two 350 bridges which I am trying to configure between two buildings. The first is configured OK as a Root Bridge. However, the second only offers Root Access Point, Repeater Access Point and Site Survey Client. It does not offer the Root Brid...

I have a cisco 1200 ap 13JA IOS version and i need to upgrade it to the next version.I am trying to upgrade through SNMP using the flash mib but it fails with InvalidSourceName errorThe entries i set in the mib areciscoFlashCopyCommand.1:-->copyToFla...

I am looking for a solution to authenticate a 350 Client against a MS Active directory via a 1200 AP (on 12.2(13)JA3 code). I was reading about EAP-FAST and it "says" it will do it, but when I attempt to set this up, I get an error in Windows Event v...

Hiwhy does the peap authentication also work if you dont push the root ca from the acs ca to an client.it seems that the peap authentication also works if you dont click on "validate server certificate" (under: http://www.cisco.com/en/US/products/sw/...

Hello,I have installed Win 2000 on the Axiomtek P1000-370 unit. It's motherboard is SBC8360. It has a PII 850 processor. This system boots fine without the client adapter installed but when installed in the PCI riser card the unit will not boot. It f...

I'm setting up MAC address authentication and need some way to bounce users off when they are blacklisted. Using SNMP, is there any way to force every wireless client to re-authenticate on an access-point?

Hi,I have observed that it is not possible to configure WPA-PSK in Cisco Aironet Client Utility for Cisco 350 series adapter.WPA-PSK is supported in Cisco Aironet Desktop Utility for Cisco AIR-CB21AG (802.11a/b/g card bus adapter).Is there any work a...

Hi,is there a way that a/b/g cardbus client will work on HP ipaq 5450?There is no driver on cisco software downloads exept for XP and W2000.tnx, bye F.