Wireless

cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

review


Labels

Forum Posts

I know how to configure the AP to enable WEP Key rotation, but do you have to enable this same setting in ACS v3.1? If so where would I have to go in the ACS to do this?Thanks

c.tenley by Level 2
  • 1067 Views
  • 1 replies
  • 0 Helpful votes

I have setup an AP1200 and client with DLink DWL-650. AP's authentication is setup as 128bit with shared key. The client is running windows 2000. The client can connect with the AP and this is verified by looking at the AP's log, I can see the IP add...

globedie by Community Member
  • 583 Views
  • 1 replies
  • 0 Helpful votes

We have installed many Aironet 350 cards in W2K and NT laptops with no problem. Our CIO has a Compaq tablet running XP. I have disabled the onboard Intel card and the 350 seems to be installed OK and functioning. We use static WEP,128 bit. The tablet...

I've been trying to get PEAP working with the following devices:CiscoSecure ACS 3.1Compaq TC1000 Tablet PC with latest drivers for built in wireless cardCisco Aironet 1100 API believe everything is configured correctly on the AP - I have Open and Net...

I have a number of AP1200's installed which were passing a DHCP allocated address to wireless clients using the Primary SSID (open).I now want to manage the AP's from the wired-side only. I have set up a trunk on the 3350 switch using VLAN_MAN as the...

fearon-j by Community Member
  • 720 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Diversity Antennas

Do you HAVE to use diversity antennas to use the diversity feature on 1200AP's? Or can you use, for example, 2 seperate patch antennas.

fpineda by Level 1
  • 759 Views
  • 1 replies
  • 0 Helpful votes

Have a Cisco Wireless Access point 340 and the speed degrades as users move down the hall, away from the unit. The 340 is in the ceiling in the middle of the office. What part should I get to increase the distance for the 11 mbps range? An antenna or...

mmays by Community Member
  • 859 Views
  • 3 replies
  • 0 Helpful votes

Hello,I've installed an AP1100 and a Wireless client (AIR-PCI352).When I run ACU, all seems ok, I can see the AP etc..., all tests are ok too with 95%/100% signal.I can ping the AP to (10.0.0.1)Here is my problem :Under Internet Explorer, when I type...

nrousseau by Level 1
  • 552 Views
  • 1 replies
  • 0 Helpful votes

Hello,how can I setup activity client station timeout? I have aironet 1230 with IOS 12.2(11)JA1. In aironet 1220 with VxWorks it was possible to setup this on the page "Association Table Advanced Page" by parameter "Default activity timeout Per devic...

mikulec by Community Member
  • 725 Views
  • 2 replies
  • 0 Helpful votes

I am a CCNA supporting a few offices that have VPN connections through local ISP to a central site. I have one site that is remote and unable to get a broadband connection. It is aprox. 1.5 miles from a site that has a broadband connection. I wouls l...

support by Community Member
  • 757 Views
  • 2 replies
  • 0 Helpful votes

Hello,in our scenario we have two wireless phones on a AP1230. We can dialing out on both phones. We also can dialing direkt from one 7920 to the other 7920, but we have only noise in the line. Over a conference call whit a other phone we can speak f...

m.holfeld by Frequent Visitor
  • 1240 Views
  • 5 replies
  • 0 Helpful votes

I am in need of gathing information for various AP's (350 adn 1200's). I have used the LOG information in .txt format. This is pretty conviluted and I need to do dayly log's for a thin client program and I rather not manually put this in readable for...

tlchant by Level 1
  • 564 Views
  • 1 replies
  • 0 Helpful votes

do you have any issues encountered when you place the access point in an AHU room? I plan to place one here but afraid that the interference level. I have no experience on this.Thanks.

c.ong by Level 3
  • 802 Views
  • 2 replies
  • 0 Helpful votes