Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
HiI've seen various discussions about this but none seem to fix my issue. I have an SSID that redirects perfectly well with Windows and Android. However, Apple devices don't play. I usually get redirected to the login portal and log in successfully...
Hi I have an issue with my Guest portal in my Cisco C9800. Weh i try to connect to my SSID Guest, I have An Ip I can lunch the web portal by https://192.0.2.1 but the Web Portal not appear mannually or maybe 1 time / 5. Do you know how to resolve it ...
I get such an error when we pull the configuration file from the (physical) 5520 model WLC and upload it to virtual WLC.unsupported CLI: 'config lag enable' is invalid on this platform
Hello. I have the following scenario 3 sites (A,B,C) with 1 WLC located at Site A. We use the same SSID's at every siteall Access points at every site are in flex connect mode. The SSID's are configured for local switching. I have three flex connect ...
Hi all,I have two Cisco AP AIR-CAP2602I-E-K9 and a Cisco WLC 2500.WLC is running firmware version 8.5.171.0In this moment AP and WLC are in the same VLAN.I get this error messages from Access Point CLI (I connected it to my laptop using serial cable)...
I can see the client TX rate to AP, but is it possible to see what kind of TX rate AP has to the client?The accesspoint knows which rate it sends data at, so sounds like this should be able to be seen somewhere. In Windows it is simple to see tx and ...
Hello,I have a setup with a WLC 5508. The APs are in local mode and I am using a radius server to autoassign VLAN and to authenticate the users via 802.1x. I have created all vlan interfaces on WLC controller.Some of the clients are complaining that ...
I am running into a very strange issue. Trying to setup and ACL rule under Advanced > Security Settings on the 140AC web interface. For some reason it will not accept the mask for the IP I entered. I don't see the problem. Did I miss something or...
Does anybody knows something like that. We are trying to do throuput test with ekahau and C9115AXI-Z, but the Ekahau does not recognized the WLAN that already are associated in the LAPTOP.
Hello Professionals,Our company is using WLC 2504 controller and most of WLANs can be used by registering mac-filtering.Some of users are configured 'Any WLAN' and specific interface in order to connect each WLAN for their purpose.However, sometimes ...
HiSo this morning we upgraded one of our Cisco 9800-CL clusters from 17.3.5a to 17.3.6.All C9115AXI-B APs (14) on a certain site did not join after the upgrade.The pre-download went fine, but when I finally got a console to one of the missing APs it ...
Hello, My customer would like to migrate all APs in all sites to flexconnect. All APs on remote sites will join a central controller located in datacenter. Users will connect to a locally switched WLAN. 802.1X authentication with EAP-TLS will be us...
Resolved! WLC 9800-L-F jumbo mtu enablement
Gentsi need CTS inline-tagging enabled on the uplinks of my HA SSO 9800-L-F. sources i found so far referred me to jumbo enablement on the UCS-hosting platform (expectedly using CIMC access :0). failed to find how to access UCS's CIMC on 9800-L-F tho...
When o Access Point was in Autonomous, the interface was "state up protocol down" in "show int g0", so I change manually speed/duplex (100/full) and was "state up protocol up", so converting the Access Point from Autonomous to Lightweight and happene...
Resolved! Bridging AP's, 1310 EOL
What is replacing the 1310 AP's in order to create a wireless bridge between sites?
