Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi, This Wireless meeting room device cannot connect to the Meraki Guest SSID network. The only change that was done - switch the client IP assignment from Local LAN to Meraki DHCP on Guest SSID. Tried connecting the Device to hotspot & it connects s...
Hello everyone.I am using a Cisco Catalyst 9800-CL controller version 17.9.4 hosted in a cloud data center. In our ten offices, the default configuration includes a Cisco 1111 gateway, a 9200 switch, and 3 to 5 9130 access points. Each office is conf...
Resolved! Unregistered 9800-CL
how to avoid the consequences of not registering the device?Mar 28 20:40:15.994: %IOSXE_EWLC_LICENSE-2-MSGDEVICENOTREG: Unregistered 9800-CL can only be used in lab. For production usage, please register this device in 24 days. Failure to do so will ...
If I have 4 MR86s setup in a square 25 feet apart, does the Meraki controller automatically evaluate the RF environment and adjust the frequency and power levels to avoid interference and optimize operation for all APs?Thanks,Gil
What hardware/model can be used to extend a network and support multiple VLANs via wireless, my current setup looks something like this:I already have the layer 2 switches and router just need the access point to make the wireless bridge, I tried alr...
Hi,An upgrade of Catalyst 9800-40 from 17.3.5a to 17.9.3 ended in an endless boot loop. Most likely because it was forgotten to upgrade ROMMON from 16.10(2r) 17.7(3r). After breaking boot process, boot old system the config was gone. Restored the sta...
Resolved! The finer points of System Manager
I am trying to improve my understanding of System Manager and System Manager Sentry when used for Wireless Authentication.As I understand it, a corporate WLAN can be protected by dot1x and EAP/TLS by setting the WLAN's SSID to "802.1X with Meraki RAD...
Hi,I am testing the configuration where "Sign-on with my RADIUS server" is enabledAnd when device connects for first time I do not see any initial RADIUS Access-Request message, but Splash page is coming right away.But what if device already pre-auth...
Hi AllCan anyone tell me what solutions are out there for large area wifi coverage, for example we need wireless to be available in a large quarry site, other that sticking access points everywhere which is difficult and costly, are there any other s...
Buenas, actualmente la serie 1140 de Access Point ya no se mantiene, por lo cual no encuentro forma de descargar el IOS. Si alguno de ustedes tendría forma de acceder, se lo agradecería mucho.Necesito la imagen c1140-k9w8-tar.124-25d.JA.tar ¿Alguien ...
Hello,Please i need guidance on how to configure C9120AXI-E access point.The plan is i have a big hall that can accommodate 500 persons, i have a Cisco 9300 24p switch and 8 piece of C9120AXI-E access point. Please i need steps on how to configure th...
hello. I am trying to perform web-auth by obtaining a new public certificate and replacing it. At the same time, I plan to change the virtual IP as well. I saw in the documentation that the virtual ip should be set to a non-routable ip. Is it the sam...
We have two Cisco 9800-L-F Wireless Controllers in an HA pair with RP. When there is a failover event the GUI is no longer available.You can navigate to the GUI page and login but after that all you see is a white screen. We still get pop-up notifi...
Hello everyone, I just got a monitor AIR-AP1800S-Z-K9 and it has no ethernet port, only USB. Wrondering if it is possible to deploy it using some kind of deployment SSID, just like Mobility Express does or if I´ll need to buy and Ethernet/USB adapt...
Resolved! AP1852E rebooting loop
I have an Cisco AP1852E that is entering in rebooting loop and the message is: "SMP: failed to stop secondary CPUs"
