Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hi, We had an issue with APs whose certificates have expired. However, we have upgraded the WLC to the fixed version 8.5.182.7, but I still have the same problem. What could be the solution? When I enable 'config ap cert-expiry-ignore {mic|ssc}', the...
Hi everyone,we have one SSID which is distributed to all access points and uses its own VLAN per building. This means that I distribute a separate tag to the access points per building, so that only a specific VLAN is used at this point. This works s...
Hello, I hope you are well. I have a question about the cisco WLC3500, if I perform a factory reset on the WLC3500 controller, will the permanent licenses that are in it be lost? Thanks in advance for the support.
Hi, I have a WLC 9800 and I want receive alerts of Rogue Malicious (Rogue APs and SSID) by email. Is it possible to configure this on WLC 9800? Another possibility would be to send this alerts from WLC 9800 to Solar Winds Monitoring (NMP). I don't fo...
Buenas,Necesito montar un sistema de autenticación wifi mediante certificado digital, sin sistema radius, solo con certificado digital.La ideas es que usuario tenga un certificado y en panel de cisco tengamos mismo certificado y que cuando haga conex...
Hi All,I would like some help on how to proceed in debugging the issue below for example, what type of logs etc. to collect and analyze. Issue: I have 2802i in mobility express mode with 8.10.185.0 version installed. Another 2702i connects to this ME...
Hey there,is it possible to use content filtering (Adult, Gaming etc.) via Group Policies just with MR Enterprise Licenses?There will be no MX in this installation, content filtering should all be done by MR.Do we need Advanced or Enterprise Licenses...
Hi, everybody. I need your help. I'm working at huge warehouse. I've lost one of the Cisco 1832 AP and i just have a serial number of that device. Is there a tool to find Cisco AP on local network by it's serial number?Thanks in advance.
I have sensors that claimed to DNAC and running while on wireless backhaul, but I am not able to ping them or SSH, even I have enabled the SSH. Also when I try to connect them through wired on a vlan has dhcp enabled option 43 still unreachable on dn...
Hi Team,I have recently deployed the Cisco Meraki MR-56 Access point, Switches MR-210 and MR425.here is some advantage for Meraki deployment this is very useful instead of other devices 1 - Easily managed by Miraki Portal.2 - All access points and sw...
Dear All, Here is my facing problem. I have a wildcard certificate applied from a third-party CA Authority, according to the configuration file, I can't find the steps for installing it for Web Admin and WenAuth. Does anyone have some experience with...
Resolved! NPS Authentication and WPA3
I'm setting up a new Wi-Fi network with RADIUS authentication. It will have 20 Meraki CW9166I APs installed on an existing Cisco switch network, with known good DHCP and DNS services. There is already an NPS in place, and having entered the NPS addre...
Hello I have a cisco 2500 series wireless controller with two AIR-CAP1702I-E-K9 antennas.Here is my problem when I connect to wifi everything works I can access the internet from my phone or laptop. But on the other hand I don't see any computer or p...
Resolved! AP Tag via API
Hi guys, I have a question.Is it possible to create a tag via API and add specific APs to this tag?Unfortunately I have not found any information about this on the net.Thanks.
Radius auth stopped working with "failed to connect to the RADIUS server."Ping works, Radius servers works fine with all other wireless networksand it seems from packet capture it don't even try to send anything and immediately fails.We have 3 MX67W ...
