Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Dears,i've got a strange Problem with a pair of 5520, IOS 8.5.182.0: 2 Weeks ago i did a reboot of the cluster, Machine 2 failed to boot and is dead. We had a spare Machine and installed it today. Update IOS, Configure Interfaces, not the biggest dea...
Hello Cisco Wireless-ExpertsI'm on my way from Cisco Prime 3.8.1 to 3.10.4.After settings up a second machine in parallel and doing the first upgrade-steps I noticed the following error-messagewhen I type in the command "show application status NCS" ...
I have a 9800-CL in AWS which is reachable via GUI and CLI. When I try to add a WLAN, it wil not accept any WLAN number and the security tab is completely blank with no options at all. I don't believe this to be a licensing issue as the licennses are...
Hello all,I recently configured a physical WLC C9800-L-F. Here are some details about the WLC that could be useful:Model: C9800-L-F-K9Firmware: Bengaluru-17.6.4I configured two Switched VLAN Interface. One of them is used as management interface in V...
Hello, I am trying to configure a C9300 switch for wireless capabilities. I'm currently running Cisco IOS XE Software, Version 17.06.05. I have enabled the wireless controller, however, I am trying to add a WAP and struggling to get this figured out...
Hello,I am looking at replacing a lot of older Meraki APs and iv been going through the spec of all the possible MR units to decide what to replace them with.Going through the specs, it seems that the main difference between them all is the bandwidth...
Hi,I have a C9800-L-F-K9 running on 17.9.2 code where not matter what WLAN config I apply within the tag, it will not broadcast on the AP.Issuing a "show dot11 wlan" directly on the AP shows no thing applied to radios:L02TEST#show dot11 wlanRadio Vap...
Hello. I have a vWlc (8.5.182.0) and some ap's, one ap is a 2802i. The controller sets both radios of the 2802 to 5ghz when i want one 5 and one 2.4. I have turned off Flexible Radio Assignment but it dosent work. What have i missed?
Those ACLs areACL on 9800. not user generatedIt appears to have been created by WLC itself. Could you by any chance know the purpose of each ACL? -IP-Adm-V4-Int-ACL-global -implicit_deny -implicit_permit -preauth_v4 -meraki-fqdn-dns
I'm looking at high channel utilization issues in DNAC (v. 2.2.3.6) from an 9120i connected to a 9800 v.17.3.4cSeeing high channel utilization, low interference and low tx/rx utilization from the AP. Is it correct that there is some other 802.11 devi...
I have a problem configuring Cisco Air CAP2702i-F-K9 AP 1. I can not get into terminal via serial port 2. I want to do reset, using hard reset but always fail (do the steps in hard reset of cisco device are all the same?) can you give me the solution...
my architecture is end devices connected to WGB Cisco 1562EAC LAN and WGB connected to acces point WGB cisco 1562 can connect to the access point properly, the problem is WGB to some end device that goes through the same UTP cable RTO randomly, somet...
Hi,I recently bought a new android terminal (Zebra MC2700) which unfortunately has disconnection problems causing the connection to be lost with an As400 client (Mocha app), my network is made up of several devices.AIR-AP1852E-E-K9 (4ap) AIR-CAP1602I...
Due to COVID-19 lockdown, we've implemented MS Teams a few months back.Now that small number of users are back in the office and using mobile devices for Teams, we started receiving reports of some issues on corporate mobile WLAN (MDM managed iPhones...
Dear All, I have a question would like to ask regarding to the following, our customers reported that one of the site that using Meraki MR44 having the following issue when roamed from one AP to another, and checked in the dashboard and see the follo...
