Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi, This is my first time configuring a Cisco 9800-L controller.I think I've accidentally deleted the boot image because I tried to perform factory reset after messing with the controller.Now I'm able to boot from a tftp location. However, after gett...
Hi~I know if want to request RMA, you need to access meraki dashboard to open a case.But except this, is there any other methods to request RMA?If anyone can help me on this ,I will be appreciate.https://documentation.meraki.com/General_Administratio...
Hello all. I am very new to Meraki and still learning my way around. We have sever sites running different MR series access points and a lot of them are showing a disconnect that lasts about 3 minutes. It almost looks like it is on a schedule. I am n...
Hello,on Cisco EWC is it possible to restrict the access of "guest" users only to a specific SSID, in this case the designed SSID for a guest user. We saw a guide https://wifininjas.net/2019/10/24/wn-blog-017-cisco-c9800-local-web-auth-config/, but w...
Hello.(Please see attached screenshot.) device= MX64W-HW , IOS 16.16I need to enable SSID broadcasting, yet when I navigate to "Wireless settings" I have very few options.How do I access the functionality displayed in the below part of the attached i...
Meraki says that MR32s can only run the latest version of 26.x.x, but the changelog says that we can install the latest version of 28.6.1, the MR32 will run MR 26.8.3. So can the firmware on these MR32s be upgraded to 28.6.1?
How to configure guest LAN,open no password,only internet passthrough, no visible internal LAN clients.Same poe switch,with all AP on,one WLC port for all AP.Seperate wlc port for home VLAN and seperate for guest,same switch.Or two switchs, and two ...
I have 10 working standalone 3500APs.Now im buying used WLC. So can i convert back to light wlc AP from WLC remote?Or i must manualy go to each AP and convert back to wlc AP?
When you read the help for EDCA see below. it states use WMM when voice or Video services are not deployed on your networkBut WMM classifies voice and videointo different classes so why not use it. I have a mixture of Ascom i75s and Cisco 7921,7925 p...
Hi everyone,Client looking to upgrade small business cisco equipment to latest technology. 2300 sq ft space on one floor. Currently has RV-134W wireless router and 200-26 gigabit smart switch and using a WAP. Client currently using 13 devices wired t...
I am a wireless LAN mobile device developer.My customer is using WLC CT-8504-K9/8.3.140.0. It was released on Jan/30/2019. Problem is my device can't associated the customer AP as below debug client log.But, number of clients connected to the AP is ...
So this is odd, when I go into the WLC9800 and change VTP (shows client and MST transparent) to transparent I lose my CAPWAP tunnels and APs do not rejoin? VLANs are still on controller and nothing changes. Any idea?
Hi,What are the points must be included in wifi 6 ap deployemt Thanks
I'm searching for a solution to convert Wi-Fi to LAN I have an area where 1G WIFI available but I need to provide network connectivity to 10 desktop via ethernet Is there any product I can use to convert the Wifi signal to LAN and deliver via a sw...
HI ! I have a lot of 87 Assorted CISCO Access Points (3502E_A_K9 and 3502I_A_K9). I want to sell them but before, I would like to know how could I do a diagnostic test to see if all of them are properly working.Thanks!
