Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Dear Sir, I tried to download and install 3rd party certificate to WLC SW v 7.6.110I followed the steps as this link saidhttps://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/109597-csr-chained-certificates-wlc-00.h...
Hi I'm in the UK, already lead to believe we can use these channels of 5Ghz , just need to make sure the APs are fast enough to move off if detected radar which they are.We can only use 7 of he 9 channels on 40Mhs, so want to test before going to 20M...
Resolved! Prime & WLC interfaces down
Hello all. After installing a backup controller a few months, I now have regurlarly those kind of critical alarms in Cisco Prime 3.0.2I only got 2 conneted interfaces in my WLC0 (port 1 and port 2).. I recieve these traps saying that the remain port...
Resolved! Interference on 2.4 GHz
We have a newer Meraki wireless deployment. The building is a 2-story office area attached to a large warehouse. Our 2.4 GHz wireless is not working reliably in the warehouse portion of the building, the 5 GHz wireless is working. I am already wor...
Resolved! Viewing Wireless Cleints
Hi,Company has issued a return to office policy and lots of our users are using laptops. I want to view the list of clients that my APs are handling. What I'm doing right now is opening my APs on different tabs and let the Carousel addon to flip to t...
Resolved! Chromebooks and 3802 access points
We've just completed some network up grades at four sites. New switches and new access points. The access points are 3802's. The problem is some of our older Chromebooks no longer connect to the 3802's. Swap out a 3802 for a 3702 and the Chromebo...
Hi WLC 8.5.140.0 needs to remove http for security reason. Is it possible to remove it without upgrading ios? thanks
Hello, I noticed on our 5508 WLC that an access point on the roof of one of our buildings is down (roof terrance). On the PoE switch is now shows Ieee PD instead of AIR-CAP1532E-EK9I have done a shut and no shut and I get the same. Nothing shows wit...
Hi, I have a WLC 2504 running ver 8.5.171.0The issue I'm having is with laptop clients connecting to our guest wifi. They do not get the web login page to enter their credentials for guest wifi access. It attempts to redirect to https but gets stuck....
When i configure the ap with Static IP it takes IP and Starts ping in local network but it cant join WLC.
I have recently purchased some MR56 APs and get this message when saving an RF Profile. Why am I now being forced to select a UNII-1 or UNII-2 "5-lo" channel?There were errors in saving this configuration:One or more errors occurred. No changes have ...
Hi guys, Some of users have a issue after AP upgrade from AP1832-I to C9115AXI. Users report their whatsapp web shows disconnect when phone screen turned off. The WLC is using 3504 with firmware 8.10.162.0. I tried debug client and marked the debug d...
Resolved! How do I use the 2.5GB port?
I have MR36 & 46 AP's. We are using Fortinet 426 switches that have the 2.5GB multigig ports. I tried to connect the 2 with a normal cat6 cable but the port speed stays at 1GB. Is there something I need to do on Meraki's side to turn this function...
Hello Team, i am getting this below error when accessing the network device after creating policy to access network device for internal users. TACACS+ will use the password prompt from global TACACS+ configuration but same device i can access using ...
Hi,As per the data sheet Cisco Catalyst 9115 ap is supported wifi6 . my switch C9300L-48P-4X-E supports only poe+ so what will be the impact Thanks
