Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Resolved! AP3802 not joining WLC5520
Hi All, I am having a challenge on an AP3802 not joining the WLC.The WLC runs on version 8.3.143.0, while the version of the AP is 8.2.151.0. All other APs have connected, though this AP was used to replace a bad AP, as it was not with the other APs ...
I am attempting to use a 1832i as a wireless bridge for an IP camera to an existing 1552H WAP network. I have joined the 1832i to the Network by ethernet cable so I could set it up. I have no problem with the WAC seeing it with a wired connection. I...
Hi , I am trying to add the 15 AP adder license via GUI for 2504 WLC with 8.5 version in HA N+1, note that as per guide i should be getting as belowStep 1Choose Management > Software Activation > Commands to open the License Commands page. But comman...
Resolved! Mobility Express with client separation
Does Mobility Express support client separation within a wireless vlan? I do not see any options for this in the ME configuration.
Hello to all! I apologize in advance for bad english ... I would like to know if someone faced this problem: there is cisco wlc 5520 8.2.141 and external captive portal. we are trying to set up this bundle so that the client ONCE is transferred to th...
Resolved! Windows 10 client connected to a SSID encountered duplicate IP error message in specific context.
Hello, Many Windows 10 clients connected to a specific 802.1x SSID encountered duplicate IP message error in a specific context: going back to wireless network after few days or switch from wired to wireless network.Our WLC version 8.0.152 and 8.3.14...
We wanted to upgrade our WLC Software, but some of our hardware AP's are not supported anymore. We do have several 2600er models.Firmware 8.5.140.0 Released June, 2018 -> supports 2600 modelsFirmware 8.6.101.0 Released December 2017 -> does not suppo...
Hi All, I have a root bridge 2702 AP and 5 non-root bridge 2702 AP's. The root bridge AP is connected to the network physically. The other 5 wireless bridge to the root bridge. What I am finding is that some of the non-roots are up and associated t...
Hi Folks, I am in the process of moving from 8510 to 8540 wireless controllers, is it ok to backup the configuration from the 8510 and store it on the 8540 ? or better to do the configuration of the 8540 manually. Thanks Aous
Hi, we're deploying a demo network for a customer and after a few hiccups it seems to be running properly. One of the problems was an oversubscription of customers on a single GE link to the controller, which I seem to have solved by adding a new lin...
I am having issues adding additional AP's currently i have 15 aps no problem but trying to add 2 more and no luck , they do show under statistics ap join with ip addresses assigned but status not joined.also found this:Reason For Last Unsuccessful At...
I purchased a AIR-CAP2702I-UXK9. I am trying to prime the AP but the controller will not allow it to accociate because the Country is not set. Is it possible to configure the country via the CLI? Thanks!
ap AIR-CAP1532I-D-K9 not join with wlc 3504 showing error in wlcosapiBsnTimer: Feb 26 15:32:14.307: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:3224 Failed to complete DTLS handshake with peer
Hi,i try to setup a mesh network (bridge) to connect two building together. The mesh network goes up successfully but can't pass anything over the other building.Here is my setupWLC5520 version 8.5.160Two AP 1562D, one as RAP and one as MAP, both eth...
I currently have Guest wireless working and the setup is with Guest anchors. Clients can only connect at 54Mbps. Is it possible to get faster connection speeds? My setup is just like what is shown in the "Cisco Guest Access Using WLC with Anchor...
