Hello all,I have multiple regional locations w/ 5520 WLCs. These WLCs are connected to a Nexus 9k (Services) -> Catalyst 9k (CORE) -> Router. The associated APs are connected to access switches -> CORE -> Router. I have a Guest Wireless SSID set up w...
Forum Posts
Hello,when installing, the following error message appears:wlc01#install add file tftp://spy/C9800-40-universalk9_wlc.17.03.05b.SPA.bin activate commit install_add_activate_commit: START Sun Dec 11 12:48:06 cest 2022Downloading file tftp://spy/C9800-...
Hello Cisco Community,I'm seeking assistance with generating a Certificate Signing Request (CSR) file for HTTPS access on my newly acquired Cisco 9800-80 Wireless Controller. I'm aiming to establish secure communication through HTTPS, but I'm encount...
Resolved! Change Transmit Power Level on 2602 AP
Hi,I need to lower the transmit (tx) power level from the default 1 to something less powerful like 4 but I don't see any way to do it through the WLC (Cisco 2504 WLC) and I can't figure it out from the CLI. Also, I saw a tutorial on how the lower th...
I have recently been testing EWC capability and failover in various scenarios running on 9130AXI APs and have a query regarding configuration files remaining up-to-date across multiple devices.EWC seems to work fairly well with dynamically allocating...
Hi, We have 2 9800-40 controllers on versions 17.3.6 and 17.9.3. Both are configured with the same join profile and capwap configuration.They have CAPWAP Advanced -> Data encryption both turned off. If we capture the packets on the controller running...
I am getting exclamation sign against Redundancy configuration, RMI IP for chassis 1 and RMI IP for chassis 2.This is an HA setup and I am running 17.3.4c. Following is the redundancy outputXXXXXXXXXX-003#sh redundancyRedundant System Information :--...
Hello I have an issue with a 9115E AP where for 2.4 radio is active only B connector. The question is how to activate others 4 connectors. Is this model has any limitations? My installation and AP use is that two antennas are installed in two differe...
Operational status is showing down as well as no SSID's are broadcasting. Access point is already joined with controller, the DHCP IP which is getting this AP is also pingable. Cisco Catalyst 9800-L Series WLC, I am using to connect this access point...
Catalyst wlc 9800 running 17.3.6 code (last that supports the 2702I) I have a WLAN SSID profile that if applied to a 2702I will allow old intermec ck3 handhelds running Windows Embedded Handheld 6.5 Classic CE OS 52.29354 (Build2935415i3, 12143). ht...
Dear Experts Community,I need you advice on the designWe have 2 x 9800 WLCs working in SSO mode with 400 WAPs and all SSIDs are configured with centrally switched mode.We have 1 LAG connected to Core Switches on trunk port for corporate data and voic...
Hello Cisco Community,Is it possible de configure the "C9120AXI-EWC-E" as a ROOT-AP (RAP / Mesh controler) ? My previous configuration was :2 AP1231 (Aronet 1200 series) linked together in WORKGROUP BRIDGE Mode >N°1 was a AP1231 in "WGB root with...
Hardware:WLC 9800-CL on Hyper-V - 17.9.3 Cuppertinoc9210i API'm trying to setup an SSID with WPA3 Personal security only but I'm running into a weird issue with both Windows 10 and Windows 11 (My Pixel5 doesn't seem to care)If I configure the SSID wi...
Buenas tardes,Tengo una Mesh con AP IW-6300 con 2 controladoras C9800 por HA (Conectadas con el puerto RP entre si)Aguardo que las WLC esten sincronizadas (una como Active y Standby). Entonces procedo a apagar la activa, toma el control la Stanby, pe...
Hello,I have 3 CBW 150AX, all run fine.However, when I log in to the Primary AP dashboard, I do not see the list of APs under Monitoring->Network Summary->Access Points.The following describes the situation:When I go to Monitoring->Network Summary, I...
