Hi There.We are facing a frequent disconnection of our Wireless Clients on our Meraki MR44 access points. We are running the current stable release 29.4.1 on all our access points.The user is stationed at his desk and he gets disconnected frequently ...
Forum Posts
Hello everyone, I am experiencing frequent crashes on my Cisco WLC 5508 running version 8.0.140.0. The WLC is out of support and I cannot upgrade to a newer version, and I honestly noticed that there are reports of bugs with this same task in newer v...
Important noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will upgrade to the backup version (MR 30.7.1) if they are in networks c...
We have a "guest" LAN used for the on-site health center and security. Their devices are not compatible with a portal. Is there a way to configure the GLAN to function without requiring an authentication? Physical security is very effective for these...
Given several prompts to ChatGPT but wanted to check with the experts here too.We're a Meraki MR customer since 2013. I just decommissioned my 802.11ac MRs from 2015 (MR32, MR33, MR34, MR42, MR52) for new CW9164I models (40 total) and two CW9166D1 mo...
We are planning to migrate from 5508 to 9800. So I'm trying to use the converter provided by cisco, has anyone tried it? I wonder if it's converted properly.
Hello Community,I have never worked with Cisco APs before and I have just come across two Cisco AIR-AP2802E-E-K9 access points.I would like to use them privately.The devices are currently running the Lightwight variant, as they were apparently previo...
Hi everyone,is there a way of bulk uploading networks to my organisation on the Meraki dashboard?I have 130 networks to configure.thanksJohn
お世話になっております。WLC(17.15.2)へブラウザログインしようとすると、ユーザー名・パスワードを入力後、以下の表示となりログインできなくなりました。VTY Allocation FailedNo VTY lines available to service the request. Please check the existing VTY line usage with the command 'show users' and clear the lines using 'clear...
Hello Expert , As per my understanding the FlexConnect with central auth and local switch , will keep the clients "thats already authenticated" connected , however i had the situation where already authenticated users were disconnected from AP when A...
Resolved! connect another Meraki AP to an MR36H?
Can I connect another Meraki AP to an MR36H? I tried port 1 with PoE and a power injector. The AP won't go online; it has power, but no IP address. A laptop works on the MR36H ports, so the ports must be configured correctly. I tried it with an MR28 ...
Hi team,We are using cisco business Ap 150ax in our infra and now some new 9105 APs we want to add.We know CBW do not support EWC controller. Is there any chance 9105 (in AP mode) can be used with CBW 150ax AP.Please help.
Resolved! eWC active isnt Switching user traffic
Hi, We have an issue with our WLAN: This issue is that eWC active AP isn't switching user traffic whilst all other APs are fine and the issue moves if another AP becomes eWC active.symptoms are, the users gets into RUN state and gets an IP but cannot...
Is it normal for conditional debug/radioactive trace to lose details when looking back several days? I had radioactive tracing setup for several MAC addresses over a weekend. I generated logs for a MAC going back 3 days. When I looked at the generate...
Hi,I have a WLC 9800 on Firmware OS : 17.9.319 APs and 100 Clients Everything looks normal, but there are reports that the CPU utilization rate is too high. The problem is only 7th core. Has anyone encountered the same problem as me. What should I do...
