I'm currently using a program called bgpq3 to generate prefix-sets off of IRR records for BGP session filtering. Once these prefix-sets are generated in IOS-XR prefix-set format by the program, I run a script that SSH's into the router and "pastes" t...
Forum Posts
Hi all, I'm wondering if some one may assist with netconf-yang on IOS-XRv version 6, Cisco documentation seems to be very limited here. <edit-config> and <commit> seem to work well but i am having trouble with basic things like "no <command>". Examp...
Dear Community, I have the following setup (network scheme attached): * MPLS L3VPN for Customer "A"* different branch offices and 1 HQ/DC office with Internet access via centralized Firewall* BGP is used as CE-PE routing protocol: branch sites use AS...
Hi Team,When I ingress the command "admin show environment temperatures location 0/FT1". I have the following result:================================================================================Location TEMPERATURE Value Crit Major Mi...
Resolved! Test RFC 2544 with only 1 interface
Hello I would like to do an RFC2544 test on Cisco equipment with software loop on the interface between RFC2544 tester and Cisco equipment. Has anyone already done this test with a single test device (1 interface) if yes I'm looking for configuration...
Resolved! SONET/SDH for ASR9912
We have an ASR 9912 router that is running IOS XR 64bit. We need to relocate an STM4 link from the older router (Cisco 7609S) to the ASR router to remove the old router from the network, as it is out of support for a long time now.What are the possib...
I have configured below configuration on NCS 540 Router for receiving dying-gasp snmp trap messages at my EPNM tool. Unfortunately I am not receiving any alert at EPNM tool during power outage but normal snmp traps alerts are receiving at EPNM. Howev...
Hello ALL, One of my clients is preparing to undergo a hardware replacement for their Chassis 9922. This involves swapping out the RP card; the existing ASR9900 RP card will be substituted with the RP3 card. Additionally, they plan to replace the SFC...
On an ASR 9010 running IOS-XR 5.3.3 (freshly turbo-booted): policy-global glbLocationCommunity '6', glbDefaultCustomer '100'end-global route-policy test1 set community $glbLocationCommunity additiveend-policy route-policy test3($p) set local-prefere...
I founed this log in ASR-9912 LC/0/7/CPU0:Dec 13 08:15:48.791 BKK: pfm_node_lc[297]: %PLATFORM-FCA-2-CLK_FAIL : Set|zllc[127026]|0x1046000|Device driver for device 'FMEA CLK DIAG' detected clock reference failure / DPLL unlock indicator on 'ZARLINK C...
I am trying to create a template script, but it's not working. Where am I going wrong?Template: create_l2if (if, vlan)interface TenGigE $if.$vlan l2transportencapsulation dot1q $vlanrewrite ingress tag pop 2 symmetricApply-template create_l2if (0/0/0...
Hello, I have a IOS-XRv 9000 with SSH and gRPC enabled, running on the latest version of CML2. gRPC works fine from a directly attached network, but I cannot get gRPC to work from a remote (non-local) network. Since other protocols like SSH work as...
Resolved! ASA 5525 event manager
Hi team, maybe who help me) I have ASA 5525. I want to write in the event manager if the ping is not successful (Success rate is 0 percent), then you need to execute clear crypto ikev2 sa "x.x.x.x" Check available IP once every 3-5 minutes. Maybe som...
Hello, is there anyone here who has a USB console working on these routers? https://www.cisco.com/c/en/us/td/docs/iosxr/ncs5xx/hardware/installation/guide/b-ncs540-small-density-routers-hig/m-overview-ncs540-small-density-routers.html#id_75425 In my ...
I have a 4431 and when I reboot the router, it is stuck at image validated.I went into rommon and didconfreg 0x0 and did a rebootAfter the reboot, I did confreg 0x2102boot usb0:isr4400-universalk9.03.13.02.S.154-3.S2-ext.SPA.binThe system tries to bo...
