Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2112995members
1451798discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Resolved! Advertise Non-Existent Prefix to BGP Peer

We recently contracted with Akamai for their Prolexic DDoS service.  Long story short, I need to be able to advertise to them (via BGP) any arbitrary IPv4 prefix that I own. For example: let's assume my wireless network, which uses a non-NAT /17 from...

Block access to Google Games

We recently implemented a pair of FW1120's with full FTD licensing.  Configuring access control policies to block specific websites and URL categories.One of the categories we have blocked is "games" which does a great job of blocking those websites....

spauldingd by • Level 1
  • 1902 Views
  • 12 replies
  • 0 Helpful votes

Cisco ISE design

I have customer has two DCs with almost 10K endpoints, and I need to deploy for him Cisco ISE, which best practice should be applied and include HA?Also want to know Each endpoint count as active session? or endpoint can be multiple active session? b...

Two Cisco community account

HI, Due to my cisco account issue, my profile became like new, and I discovered that my profile on Cisco community became like a new profile, although I have old profile with many posts, my question, how to restore my old profile and use it again? 

HamadaElboshy_0-1761422261850.png

privilege level command output

Hello,I have a contractor doing some work for me and he needs to see a few of my access switches.I set him up with a username with privilege 5 and used a rotary group to allow him direct login to enable mode on a specific port.Problem is when I teste...

Cisco Catalyst 1300 and Dynamic VLAN

Hello colleagues, i'm trying to configure 802.1x authentication for Cisco IP Phone (79xx series) and computer connected on its switch port and this together connected  to Cisco Catalyst 1300 switch (the new name of the SG-series SMB).  Unfortunately ...

867VAE-K9 as CO DSLAM

Is it possible to use 2 867VAE-K9 units running Cisco IOS Software, C860 Software (C860VAE-ADVSECURITYK9-M), Version 15.1(4)M3, RELEASE SOFTWARE (fc1) as a VDSL2 bridge? I have a predicament where I cant run proper 4 pair Cat cabling and need to get ...

olivieeppss by • Community Member
  • 124 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Cisco 1100 ISP Failover

Dear Forum,I'm reaching out for an issue I'm having with a Cisco 1100 running IOS 9.17.09.05. The router is connected to 2 WAN ports with a simple failover config. The primary WAN is on G0/0/0 and the backup is on G0/0/1. When ISP1 (ATT) drops, the d...

NDFC Multisite Issue MGMT inrerface DCI IFC links

Hi guys , i am testing NDFC multisite configuration over simulator EVE_ng .. deployed NDFC as a VM , and leaf and spine nodes topology under EVE-ng . For the VM external connectivity , i created a network cloud and attached all nodes mgmt interface t...

MalavSharma_0-1761370615254.png

FMC_FTD registration

We have FMC v 7.2.3 currently managing  2 ftd 4145 instances. The management was all well until when i recently discovered that one instance is not visible on the fmc.  Checked manager status on the instance and it shows registration pending as indic...

Dkiptoo_0-1761296666426.png Dkiptoo_1-1761296677840.png
Dkiptoo by • Level 1
  • 138 Views
  • 3 replies
  • 0 Helpful votes

AP fail to join WCL9800 with LSC Certificate

Hi,In my lab enviroment, I have a wlc9800m with ios xe 17.17.1 and a view ap's like 9136 and 9176 and a windows server as a CA.  The idea of the lab is, that ap's has to join the controller via certificates.For the lab setup I used the following guid...

CML SandBox Node spin up issue

I cannot spin up more than 11 nodes. I get the following error.Warning: High System Load (memory) on cml-controller: launch sequencing will be paused until system load stabilizesAnd, for some reason the CSR1000v memory requirement is always stuck 99....

SSLM: Configuring multi-tier certificates issues

Hi Guys,Wanted to know what was the preferred or Cisco accepted way to install / configure multi-tier certificates on the SSL module?  When reading the config guide, it discusses in detail how to handle a single tier cert (i.e just a root ca cert), h...

sgonsalv by • Level 1
  • 5328 Views
  • 6 replies
  • 0 Helpful votes
Load more