Trending Topics
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
-
how to see the line vty session time-out in NX-OS
by Sudqi -
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
by Thomas27100 -
the self-registration page of guest wifi portal is not being updated
by seanxiao -
Por que ainda tens o VTP (VLAN Trunking Protocol) ativado na tua rede?
by Silesio de Carvalho -
GRE over IPSEC
by georgesofroniadis -
BYOD - Network Setup Assistant (NSA) on Android and random mac address
by Daniel G. -
Webex calling (CUCM) inside Microsoft Teams
by Flemming Ortvald -
Best Practices in Migrating from NID to Official Contanerized NSO
by Pannag Desai
Community Activity
License increase Cisco 2901 router backplane Capacity to 500MB
Dear Community Members., I have a 2901 router that need to push about 500mb Data traffic via Its Gigabits Port.Do I need a License and how can i get one to be able to achieve this/
One mac address is seen on two differnet ports
The system was getting APIPA ip add. After logging in to the switch we fonud the following output : -Vlan Mac Address Type Ports---- ----------- -------- -----20 7085.c281.66bd DYNAMIC Gi1/0/3430 bd7085.c281.66 DYNAMIC Te1/1/1We checked the dhcp logs...
lost connection from DMVPN Peers
hi,i would like to express my issue and if you are able to advice me . i have a company router IR1101 with internet connection provided with private ipv4 address in the WAN interface. my company uses DMVPN in order to connect to company infrastructu...
2960x and 3850 what would happen if the eval of smart license expired
Good day, Our work is using some 2960x and 3850 as Layer2 and Layer 3 switches. As there are some vulnerabilities in the old firmware we are checking in upgrading it to the latest release however by upgrading it, it will move to smart licensing. What...
Unable to access Cisco 4221 web login page
Hi,We have a cisco 4221 router. When I try accessing its GUI page on https://192.168.10.1 its not letting me access that.What all I have tried and not working is as follows:Tried older version of firefox which supports TLS 1Tried fiddling with the fi...
Cisco Catalyst Centre - PnP/LAN Automation without SD-Access
Hello, Could anyone please give me a rough idea of what is possible with Cisco Catalyst Centre regarding the Day 0 Install of 9200L Switches that will be stacked? What benefits can Catalyst Centre bring to the immediate install of the switches such a...
Resolved! Configure "bandwidth" under interface through device/feature template
Hello. I always get useful information from community. Can I configure "bandwidth" command for cEdge router via template ? Ex) Interface GigabitEthernet1 bandwidth 5000 # Possible to config this through device/feature templa...
9100 AP transitioning from local to Flexconnect mode in N+1 scenario?
Hello experts, We are considering deploying N+1 WLC in a regional basis. The requirement is to have a backup WLC in the regional site in case the local WLC presents a failure or is unreachable for long periods of time. My question is if such an AP co...
Webex calling (CUCM) inside Microsoft Teams
Is it possible to control DND state from MS-teams status, so that busy in calendar triggers DND.
Best Practices in Migrating from NID to Official Contanerized NSO
Co-Author: @Qi Li This guide will explain the migration method from the open source container NID towards the Cisco Containerized NSO instance. To be more specific, the migration is towards the recommended Containerized NSO framework with best pract...
IPSec VPN "Up-Active" but No Traffic Passing Between Cisco and Bintec
Hello,I am currently facing a recurring issue with the configuration of an IPSec VPN between a Cisco router and a Bintec router. Although the VPN tunnel appears to be functioning correctly and is displayed as "UP-Active" on both sides, no traffic is ...
SNTC vulnerabilities Report Issue
I would like to understand how the vulnerability reporting works in SNTC. Lately, I have been noticing something strange. Not sure, if it is a reporting issue or something that I am missing. For instance, the SNTC is reporting the following vulnerabi...
Unable to claim target in EU region
Hi.When I'm trying to claim a new target from my Sandbox in Intersight I get the message:"The device has not been updated to support claim in this region. Please wait for device to be upgraded, if issue persists please contact Cisco TAC.". How can I ...
Cisco 9200 err-disable AUTHMGR-5-SECURITY_VIOLATION
Hi Expert,Recently, one port on our 9200 switch went to err-disable state and the status LEDs are all off. The port configuration is as below: it is connected to a desktop PCThe logs is as below, it looks before it goes to err-disable state, the port...
how to see the line vty session time-out in NX-OS
Hello Experts,In Cisco IOS, we use (show line vty #) to see the session time-out for a specific user,what is the same command in Cisco NX-OS,Thanks
