Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2113023members
1451809discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Can not get Internet Access [or nat translations] on my ISRC1111

Hello   I am working multiple setups but this one was supposed to be easy, until it was not. I am sure I am overlooking something tiny, but nevertheless. Long story short; here is my config and I get not get any NAT translations and or any internet a...

TheGoob by • VIP
  • 35 Views
  • 0 replies
  • 0 Helpful votes

webex auto attendant menu options routing

Hi All, I am new to Webex auto attendant and call queues ,we have configured an auto attendant in Webex control hub which will play a welcome message and then ask caller to select from two options .Option 1 will route to a call queue and for option 2...

ISE データ制限のベストプラクティス

はじめに症状解決策参照   はじめに このドキュメントでは、ISEのシステムパフォーマンスを向上させるためのISE利用時のデータ制限のベストプラクティスをご紹介します。   症状 ISE の [アラーム] タブに [高負荷平均]、[高 CPU]、または [高メモリ使用量] のアラームが頻繁にトリガーされる場合、以下のデータ制限設定を行うことでシステム負荷を軽減させることが期待できます。   解決策 [管理]-> [システム]-> [設定]-> [プロトコル]-> [RADIUS] を有効にします...

1-Suppression.png 2-EndPoint Attribute Filter.png
kyoshita by • Cisco Employee
  • 29 Views
  • 0 replies
  • 0 Helpful votes

Cisco Port isolation and shared phone/PC drops

I'm an not a network guy, understand some but the advanced stuff is above me and I know that. So I ask questions to help my understanding.We would like to block east-west traffic, and I believe that port isolation, private vlans would help with that....

tintisfadda by • Community Member
  • 39 Views
  • 0 replies
  • 0 Helpful votes

Cisco IP phone 7965 factory reset

I have some Cisco 7965 IP phones I need to dispose of. Company policy requires them to be wiped/factory reset before disposal. I have successfully wiped 8841s without issue. With the 7900 series after I perform the factory reset the screen is stuck o...

Cisco Port isolation and shared phone/PC drops

I'm an not a network guy, understand some but the advanced stuff is above me and I know that. So I ask questions to help my understanding.We would like to block east-west traffic, and I believe that port isolation, private vlans would help with that....

kolaktukal by • Community Member
  • 69 Views
  • 0 replies
  • 0 Helpful votes

867VAE-K9 as CO DSLAM

Is it possible to use 2 867VAE-K9 units running Cisco IOS Software, C860 Software (C860VAE-ADVSECURITYK9-M), Version 15.1(4)M3, RELEASE SOFTWARE (fc1) as a VDSL2 bridge? I have a predicament where I cant run proper 4 pair Cat cabling and need to get ...

olivieeppss by • Community Member
  • 152 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Advertise Non-Existent Prefix to BGP Peer

We recently contracted with Akamai for their Prolexic DDoS service.  Long story short, I need to be able to advertise to them (via BGP) any arbitrary IPv4 prefix that I own. For example: let's assume my wireless network, which uses a non-NAT /17 from...

Cisco ISE design

I have customer has two DCs with almost 10K endpoints, and I need to deploy for him Cisco ISE, which best practice should be applied and include HA?Also want to know Each endpoint count as active session? or endpoint can be multiple active session? b...

Two Cisco community account

HI, Due to my cisco account issue, my profile became like new, and I discovered that my profile on Cisco community became like a new profile, although I have old profile with many posts, my question, how to restore my old profile and use it again? 

HamadaElboshy_0-1761422261850.png

privilege level command output

Hello,I have a contractor doing some work for me and he needs to see a few of my access switches.I set him up with a username with privilege 5 and used a rotary group to allow him direct login to enable mode on a specific port.Problem is when I teste...

Cisco Catalyst 1300 and Dynamic VLAN

Hello colleagues, i'm trying to configure 802.1x authentication for Cisco IP Phone (79xx series) and computer connected on its switch port and this together connected  to Cisco Catalyst 1300 switch (the new name of the SG-series SMB).  Unfortunately ...

Resolved! Cisco 1100 ISP Failover

Dear Forum,I'm reaching out for an issue I'm having with a Cisco 1100 running IOS 9.17.09.05. The router is connected to 2 WAN ports with a simple failover config. The primary WAN is on G0/0/0 and the backup is on G0/0/1. When ISP1 (ATT) drops, the d...

NDFC Multisite Issue MGMT inrerface DCI IFC links

Hi guys , i am testing NDFC multisite configuration over simulator EVE_ng .. deployed NDFC as a VM , and leaf and spine nodes topology under EVE-ng . For the VM external connectivity , i created a network cloud and attached all nodes mgmt interface t...

MalavSharma_0-1761370615254.png
Load more