Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
1999985members
1360595discussions

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

VRF route target

I have a question in configuration the MP-VRF-MPLs scenario when I configure the scenario in site to site of P2P is easy because you configure the RTs for source and des and configure it in the other side in opposite site   but in different scenario ...

AlirezaTorkashvand_0-1731663672146.png AlirezaTorkashvand_1-1731663752602.png

Bgp AD

Hi I have a doubt if anyone could help me please! Imagine that I have the route 1.1.1.1 and I am receiving this network by iBGP and EBGP with the AS path attribute 200 200 200, the router will choose the IBGP route right?That is my doubt, if iBGP has...

Bruno23 by • Level 1
  • 116 Views
  • 6 replies
  • 1 Helpful votes

Catalyst 9163E Polycarbonate Lid Material and Fire Rating

Hi,I received a 9163E Access Point and with it being an outdoor model I expected the casing to be fully metal. I was surprised to see that the lid is plastic and after removing it states it is polycarbonate and weighs approximately 250g. Its stamped ...

client exclusion

Hello ,In 9800 environment, ap mode is flex is it possible to exclude a one client for a specific ssid.for ex: excluding the client for ssid (abc) but should be able to connect to xyz. Anjana

Anjana A by • Level 1
  • 7 Views
  • 0 replies
  • 0 Helpful votes

PBR-Route-map match track

I have question about match track please , i have understand ,if track is up ,it execute the follwoed set command ,if down ,it comes automaticaly to the second section of the Route-map ,is my Understanding true please ? . In my Lab ,even if it is dow...

FirePower 1120 (ASA) Chassis Name Change

Dear all,how can I change the chassis name on FirePower-1120?firepower-1120 /system* # set name FirePower-1120Warning: System name modification changes FC zone name and redeploys them non-disruptivelyfirepower-1120 /system* # commit-bufferError: comm...

Azad.A by • Level 1
  • 32 Views
  • 0 replies
  • 0 Helpful votes

Port Channel issue

CoreSW#sh etherchannel 13 summaryFlags: D - down P - bundled in port-channelI - stand-alone s - suspendedH - Hot-standby (LACP only)R - Layer3 S - Layer2U - in use f - failed to allocate aggregatorM - not in use, minimum links not metu - unsuitable f...

Hybrid Exchange/ SSL Decryption Error

We are in the process of setting up a Hybrid Cloud/ On-prem Exchange environment. We can successfully connect over port 443, but when we try to send emails over port 25 we are getting a SSL Block. We are using the Decrypt - Known Key rule set up usin...

tbduff001 by • Level 1
  • 75 Views
  • 1 replies
  • 0 Helpful votes

Resolved! Update nexus 3k - problem - grub

Hello everyone!I have very bad problem. I can not solve problem with update my Cisco Nexus 3064.Before upgrade I had version: 6.7I upgraded (installed) to nxos.7.0.3.I7.8.binAfter installing and rebooting sw, I saw:    [ 0.000000] Fastboot Memory ...

Full Tunneling stopped working

Hi guys!I have had VPN with full tunneling working for some weeks and suddenly the remote computer doesn't have internet access through the tunnel.I am attached the config file with minor name and outside IP removed for security reasons.Is anybody ab...

Load more