Buy or Renew
Buy or Renew
Welcome to the Community!
The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally.
New Here? Click here to learn more and get started.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
2133689members
1464180discussions

Featured Content

Trending Topics

Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!

Community Activity

Start a conversation

Is ISE 3.4 stable for production?

Hi,We're currently at ISE 3.1 patch 10. We intend to upgrade to ISE 3.4 patch 3 which is marked as suggested version now in Cisco's download portal. Since we've had many problems even with suggested software versions, I don't value a star in a Cisco ...

Retreiving Call data using JTAPI

Hi,I am working on retreiving call related data using JTAPI. I was able to get few fields using few classes in the JTAPI library. But I was unable to get the information such as Campaign name, Campaign Id, Call Started time, Disconnected Time, Durati...

HWIC-16A Configuration - Hardware fault?

I'm trying to configure a HWIC-16A as a terminal server without success. I can get a telnet session to connect, but I simply get a blank screen, no data appears to be sent or received over the serial line.The only similar post I could find was https:...

Resolved! Cisco Firesight "No any Data"

Dear Expert, I'm quite new with Cisco FirePower. I have 2 Cisco ASA5555 with Firepower and deploy as Active/Standby. We have three zone INSIDE OUTSIDE and Management. Firesight server is stay in management zone. I registered all Cisco Firepower modu...

VTP Pruning

Can someone help me understand the concep of vtp pruning.In my topology SW1 is the server and the rest are clients. Vlans configured are 10,20,30,40So as far as I know if vtp pruning is enabled and  a device in vlan 10 ping to another device on vlan ...

Help - layer 3 switch to router to Internet

Hi I am having some issues setting up a 2821 to pass internet traffic from a internet router to a layer3 switch.the switch and a pc connected to the switch can ping the outgoing interface on the router but not the other side of the link.The router ca...

High-Density Videoconferencing over Wireless C9800-40

Hi guys,I’ve been working in wireless for about five years and have never seen videoconferencing devices working in a wireless environment. My question is: Have you seen this? Does it work well?My intuition says it’s a terrible idea, but maybe I’m wr...

HiddenAir by • Level 1
  • 177 Views
  • 4 replies
  • 0 Helpful votes

Resolved! ASA 5525 Firewall failover setup.

We have two Cisco ASA 5525 firewall at Block A and Block B where the failover was not setup yet. Should i need to configure one port at firewall and install new physical fiber cable with transceiver for peer to peer connection?  

ITCompMinco_0-1763974294363.png

Cisco 9400 power supply "power-off"

We've got a concerning output when we check the power supplies in our dual 9400 core.  We're using PS3 and PS4 in the two units.  All four power supplies are connected to a good source.  PS4 on Core 1 is connected to a 125V power source, the other 3 ...

cisco SSE ZTNA issue with SMB Traffic

Hello Community,we are facing an issue with the SSE Ztna when we are trying to Access SMB server through a Tunnel. the behaviour is so strange when we have tested with Customer org Laptop it is not access the File server but from a laptop not from th...

Load more