Hi,Apologies in advance but im new to MPLS, But is possible to have more than one pysical interface in a tunnel and is it possible load balance accross the physical links ?
Hi Experts,We have a network running MPLS TE tunnels in the core. Cisco CRS-1 (IOS XR 3.5.3) in the core layer and 7609S (IOS 12.2(33)SRB2) at distribution layer. MPLS TE tunnels form full mesh from any 7609S to any other 7609S. It is in production.D...
We have one network link need to run MBGP using interface establish, not use loopback0.I tested from lab environment and ping test from R6-CE src:6.6.6.6 to R1-CE dst:1.1.1.1 fail, becasue ldp label pop at R4, not R3.R3 should be Penultimate Hop Popp...
Hi,Is there any way to use the IGP cost between PEs, and pass that into the VRF prefixes?For example:A branch site has 2x CEs (CE-A & CE-B), each with a link to a different PE (PE-A & PE-B). EBGP is used between CE-PE. IBGP Between CE-A & CE-B. CE-C ...
Hi, We have a customer, who is getting intermittant poor response issues over their MPLS network.When they experience these issues & do a traceroute between the 2 sites, they get the following output...traceroute to 10.0.0.2 (10.0.0.2), 30 hops ...
Hi Guys, We have a MPLS based core network. At this stage they have 2 sites in Different cities. We configured xconnect for them. Both sites are ethernet based..Because it was point-to-point we configured xconnect..Now they have a new site comi...
Hi thereI am planning to migrate our whole network from TDP to LDP gradually. Is there any issues in dhaving TDO & LDP running on same box during migration phase. and when I assume session will be down temprarily while tearning down TDP and setting u...
Hi all,Is there any options to see what tunnels are passing through one router . for ex: i have logged in to R1 then how can i see which tunnels are passing through R1 and their status.Regardsthanks in advancemahesh
Hi,I am thinking of a capmus MPLS solution where I need to collapse the functions of PE/CE and Edge switch into a 6509 switch. Wondering if this has been done by somene previously! The csutomer does not want to run Layer 2 between the access switch a...
Hi,To connect 10 sites to head office whcih technology would be better VPLS or MPLS? I would add more sites later on and it should have voice, video and critical application qos support. I know MPLS is better than VPLS in some respect. But VPSL comes...
Hi,I have a design issue for which I really like your help.In a MPLS network there are twoPOP gateway routers (G1,G2) peering with various MPLS VPN Service providers via B2B vrf eBGP peering are in 4 different ASN's. They inturn all peer via VPNv4 eB...
Dear Members,i have a problem with redistributing OSPF routes in my MPLS VPN. My local routes are redistributed into the MPLS VPN which is running BGP. This is the configuration of the edge router.!hostname CU_EDGE01!ip vrf CU_Ard 100:26route-target ...
Can anybody confirm if you can establish an Xconnect between two 20Gb port-channels (2x 10Gig bundle). The core is 40Gig and running MPLS. We have many gigabit pseudowires running over it already.Our intention is to terminate 10Gig server traffic o...
I'm new to MPLS and I have a question related to the network design.We are trying to do a layer 3 VPN across 2 geographically seperate sites.We are using two ASR 1004's for the PE's at each site. My question is this: Do I have to have a CE router o...