Good day.I am trying to get an image from the Cisco ASA and I get an error. Please tell me what could be the problem.error text: PI_SWIM_20012:Image Collection has not succeeded from device. Starting copy image from 2967972 using FTP. 2967972HANDLER_...
Forum Posts
Resolved! "SER Parity Check Error"
I'm having a bad week - my ISR 4331 router has been flooding my syslog server with these messages non-stop and I can't seem to find why:Sep 29 15:38:54.415: %IOSXE-3-PLATFORM: R0/0: bcm_switch: unit 0 SER_ERROR_0 REG unexpected NACK failure! Sep 29 1...
Resolved! Subinterface SNMP issue
Hello All I have upgraded ASR-1002x ios version from asr1002x-universalk9.03.16.09.S.155-3.S9-ext.SPA.bin to asr1002x-universalk9.17.033.SPA.bin .No problem but very strange thing occured. I have subinterfaces in configuration like Gi 0/0/2.501 .......
Hello, I got Cisco Prime up and running like I need it. Did have an interesting thing happen where the resources were lowered a bit and the Compliance Service was no longer appearing. We changed it back but the service never came back we had to rebui...
I just got in a NEXUS 2232TM-E 48p switch. The console port is a HDMI cable and I'm not familiar with using an HDMI to access it (Old school). Can anyone guide me to a place on how to access the console?
Hi, How to bridge mode G1100 verizon router ? I have ASA 5506 behind the verizon router. everything was working perfect untill the power went off and then when came back lost internet. called verizon they rest the G1100 router told me to turn off the...
I'm reading about VxLAN and its benefits, one thing that is not clear to me, and have not read anywhere is if VLAN is a MUST for VxLAN to work or are both independent and can work without one another. I read about VxLAN in detail on SDXCentral and Ju...
Hi, We bought a used 3925 with SPE200 router from Ebay for lab training. no smartnet, no support.(our Data Center has full smartnet and support) on board RTC battery run out and our team (IT geeks) replaced it. My question is how to sync RTC clock...
Dear Tim Cisco I Have a cisco prime with version 3.7.1. I see on alarms and events option there are setting of alert will be sent to email in every 30 minutes (i setting 30 mins) until the cases is solved. So, i want to setting the email notification...
HelloI am new to Cisco , and need to configure SRIOV on a 100G network interface within a Cisco server , running RHEL8.3I am familiar with configuring SRIOV with Mellanox adapters on Linux, however can't find any documentation on configuring SRIOV on...
Resolved! Prime HA two Primary servers
Hi All, I have recently installed two Prime 3.9.1 appliance setups. During the install i didn't select one of them to be used as a secondary. Will i be able to join them in the HA option via the GUI? or is there steps for me to fix this without rebui...
I use Netmiko to ssh to a cisco router and I was trying to apply the BGP configuration using ssh_conn.send_config_set(). Below is a sample configuration to be applied. Expected behavior:bgp router-id x.x.x.x should be configured under the vrf address...
Hi Guys , How do I know if my switch is LAN base or LAN lite? Here is the output from a sh ver command: Cisco IOS Software, C2960X Software (C2960X-UNIVERSALK9-M), Version 15.2(2)E3, RELEASE SOFTWARE (fc3) ROM: Bootstrap program is C2960X boot load...
I have such a special question, I own a swicht SRW248G4 so this is the first manage swicht from Linksys together with CISCO. Since I used to use it, I wanted to use it now, however I don't remember the IP anymore, putty and hyperterminal won't start....
DEAR ALL MY ROUTER IS CISCO ISR4331OS : isr4300-universalk9.17.05.01a.SPA.bin I AM USING THE NBAR protocol-pack : pp-adv-isr4000-173.1a-40-57.0.0.pack I LOADED IT ON ROUTER ip nbar protocol-pack bootflash:pp-adv-isr4000-173.1a-40-57.0.0.pack force IT...
