Hi, my name is Thien.My case is that I have configuration static NAT on the ASA allowing address 3.0.0.2 (f0/0- R2) to through the ASA (g0/3 4.0.0.254)object network OUT_REALhost 3.0.0.2object network DMZhost 4.0.0.10nat (outside,DMZ) source static O...
Hi Cisco Community. I would like to setup a separate DHCP pool for the cctv VLAN with a separate IP address range set the pool size to number of devices +1 and static bind them all, then set firewall rules to stop the home LAN from reaching the cctv ...
So I am trying to get all of these PC's to pull an address via DHCP. The two on the bottom left labeled Finance PC and Operations PC respectively are giving me the error DHCP Failed APIPA is being used. Everything else was able to work. My question ...
Hi everyone, I have a new but configured basically Cisco 3560cx 12pd-s. I keep getting the dhcp conflict error messages everyday. I have an Asus GT AX-11000 router that is connected to my new Cisco 3560cx 12pd-s. I somehow managed to do a basic confi...
Hi, I'm having some troubles with the network. I tried different setups and this is one I have got. I followed different setups found on internet and tried to connect everything accordingly, but when it comes to get IPs for PCs, the DHCP ends up fail...
Hello everyone, we are currently working on an issue related to ACLs. We have two branches (site-to-site VPN) and sometimes we need to enable communication between two computers (each computer is in a different branch). We don't want to allow all com...
I'm trying to get a file on the ise local disk using ftp in filezilla. Set the server listener to my ip in filezilla In ise, copy disk:/<file name> ftp://<My ip>But filezilla didn't respond The results also failed. Does anyone know why?
Hello folks,recently I've installed Prime Infrastructure 3.10.4 Update 02 as well as the corresponding system patch. The system still wants to install "Device-Pack-1-PI3.10-14.ubf" and "PI_3_10_4_Prime_Data_Migration_Tool_Update_05-1.0.14.ubf". Both ...
Encoder has just one interface too generate Multicast and Unicast video streamsIf all ports of switch are in same VLAN and SSM is not enabled, Client1 is able to play unicast and Client 2 is able to play multicast but when number of streams increase ...
I want to shut/no shut 60 seconds after boot the uplink. The uplink has the port description "PNP STARTUP VLAN". There is only one port per switch with this description. I came up with following applet: event manager applet SHUT_NO_SHUT_UPLINKevent t...
Setting up AAA authentication for a roleThe authorization service verifies that the user is authorized to use commands in the CLI. If your privilege level is higher than or equal to the privilege level of the command, only users with that privilege l...
If you look at the tacacs profile as shown in the picture, there are custom characteristics I wonder how this works. In the case of other banders, I understand that tacacs are linked using these attributes If you add a value here, compare it with the...
Hello,I've got a couple of Catalyst switches that are accessed by the admins via SSH.For security reasons I like to change their login method from password to public key authentication.In addition to the admin users, I have a few technical user accou...
Good Day Fellow Network PeepsSo I have been working in the Industry For a while now and have been tasked to setup a Dockerized Firewall on a Cisconow for the life of me I cant figure out how Cisco Does the routing to to be able to access it from the ...
Hi, I have a PC win 10 VMware connect to router. but i can ping to this pc (lost a lot packet). I think my problem related to firewall on PC Vm NOTE: DMZ (192.168.91.250) -----> WINdown (192.168.91.2) - default get (192.168.91.2) DNS server in DM...
