Hi,I need to configure cisco router 2921 for snmp v3, can you provide proper configure ? thanksss
Hi,I need to configure cisco router 2921 for snmp v3, can you provide proper configure ? thanksss
Cisco Prime infrastructure is unable to mail using exchange. Erros: is check server configuration.
I've been tasked with finding all switch ports that are configured as Trunks. We plan to use LMS 4.2 to push (via Netconfig) new interface level commands to all user (non-trunked) ports. From my experience, this poses a problem because we do not know...
The Cisco Prime LMS 4.2 documentation says that the maximum support public key value is 1024 bits for third party certificates. Are there any plans to allow 2048 bit, third party certificates to be used?ref: http://www.cisco.com/en/US/docs/net_mgmt/...
Hi All,My LMS version 3.2 with SP 1. ANIServer status is found to be failed to run and while executing "pdshow ANIServer", observed that " Info = Application failed or was registered incorrect".Checked the ANIServer.properties, and the entry is lik...
Hello Community,Can someone please show me how to compile a EEM (Tcl) script that will be activated when a syslog event occurs. For example, I would like the script to be activated when the following syslog event occurs:%OSPF-5-ADJCHG:Also I would li...
Hi all,Can anyone provide an advice on EEM policy books? If anyone bought any of the books can you provide a review?Thanks,Sotiris
Hiwe are upgrading LMS from 3.2 (windows) to LMS 4.2 and VMWare. But now i recogniced that it only runs with ESX 5.0.We only have version 5.1 so does anyone have experience if its running with 5.1 ?Is there any plan from cisco for an official version...
Hi Everyone,I'm looking for a LAN Management solution from Cisco based on the following specifications, any recommended one?The other question, what is the difference between CiscoWorks LMS and Cisco Prime Infrastructure? which one is considered a LA...
Question,why dont i find event track in my EEM?
Hi guys , I am sorry , I am still a new Network Administrator . I have question , on how to tune the network .I am a LAN Environment . We have servers , pc and printers . Can anyone help me on how to monitor the network and tune the network ...
Hello. Wasn't sure the format for time zone when installing eval copy of Prime Infra 1.3. Set for UTC now and need to change to CST6CDT. Not sure how to change it. Can you help? Thanks in advance.
HiWe have one of the above and i cant seem to enable netflow on it.Should i be able to ?Its one of these -Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-EThanks Steve
Hi all,I am very much a newbie to Cisco networking, but have gotten my feet wet in time past... Ready to dive in again (a little) and wanted to start by downloading and installing the Cisco Network Assistant program.I did that, downloading version 5...
Hi,I have a Cisco Prime LMS 4.1 in soft appliance, all process are running in normal state and suddenlyUPMDbMonitor and UPMProcess are in a Administrator has shut down this server state. Why is this happen?I start again these two processes and stay i...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-20-2024 07:28 AM | ||
08-18-2024 03:53 PM | ||
08-18-2024 09:11 AM | ||
08-16-2024 07:00 AM | ||
08-16-2024 06:26 AM |
User | Count |
---|---|
5 | |
3 | |
2 | |
2 | |
1 |