Hi, Someone here tried to do ssl decryption in a 5500x using FTD? I did the same as i used to do in the past but this time just do not work. Thanks
Hi, Someone here tried to do ssl decryption in a 5500x using FTD? I did the same as i used to do in the past but this time just do not work. Thanks
Team, Today we were doing the image upgrade for ASA 5585 from 9.0.1 to 9.6.1. We followed the upgrade path as below 9.0.1 - 9.1.2 - 9.1.3 - 9.6.1 First we did 9.1.2 on standby unit then rebooted the standby after it come up with 9.1.2 then upgrade ...
hallo We had a active/active Cluster and the primary unit crashed and must be replaced. The secondary is up and running. The config on the active looks like : ( Failover is already deactived ) ffm-sep-dc/sec/actNoFailover# sh run | grep fail no fail...
Hello, is there a mechanism in the new Firepower that can block IP address originating from different countries? I have a site that gets bombarded by DOS and Dictionary attacks. I have called the ISP in the past but, that can be difficult in getting ...
inter gi0/0 maneif inside ip add 1.1.1.1 255.255.255.0 security-level 100 no shu inter gi0/1 nameif mgmt ip add 2.2.2.1 255.255.255.0 security-level 100 no shu exit same-security-traffic permit inter-interface same-security-traffic permit intra-inter...
Hi All, I have a private IP from one of our partner x.x.x.x and would like to nat it. Only our internal users will be initiating connection towards this IP. What should the NAT statement look like on ASA 8.5 if have to NAT the outside ip to Y.Y.Y.Y....
I have a DMZ that has a Cisco Nexus switch with VRFs as well as a physical firewall. Is it common in a DMZ environment to put the gateways for the DMZ systems on a Nexus VRF? Or should they be on the physical firewall? If they are on the VRF, then ...
Hello Forum Folks! I'm working on a problem I feel should be easy, but I'm just not able to get my head wrapped around it. Our network is configured something like this: Outside 1.1.1.1 (Security lvl 0) Inside 192.168.1.0/24 (Security lvl 100) OtherI...
Hi, I tried to configured two object nat as below: Source Y (Internet) to destination Z (DMZ) translate port 443 into 9443 - I need this for a specific solution that only answers requests from Internet on this port Source Y (Internet) destination Z ...
Searching around I see a number of posts on the same subject, but these relate to v5.X software. Relevant bits of config: class sfr sfr fail-openuser-statistics accounting! class-map sfr match access-list SFR-REDIRECT ! access-list SFR-RED...
Dear All, i don't have any knowledge about SSL and TLS kindly describe. what is the purpose of having ssl and tls in our network how can i change config from SSL to TLS with 128 bit length
Hi to everybody, I have a question about the High Availability for the managed devices. Our customer has bought two sensors and two FMC. So, I'd like to put in HA the two sensors... Them are in passive mode. How can I do it? Thanks in advance Rega...
Dear experts, What are Cisco's plans with customers who have 5585x's with firepower SSPs, will or is the unified image (be) supported? How would we go about managing the devices? Will it be through a management console like managing FP but for ASAs a...
FYI,Hope this helps someone else. I was struggling trying to get PBR working on my ASA 5515-X 9.4.1. At first I tried adding it using ASDM, but that doesn't work at all. You can create the route-map, but it doesn't apply the policy-map to the inte...
In our office, we have a two-VLAN setup with Data running on VLAN 1 and VoIP running on VLAN 2. We also have separated modems and gateways for each of them, and would like them to have segregated internet access. Below is a list of all the VLAN IP in...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 06-24-2026 08:00 AM | ||
| 05-26-2026 07:54 AM | ||
| 05-02-2026 06:09 AM | ||
| 04-30-2026 12:46 AM | ||
| 04-24-2026 07:04 AM |
| User | Count |
|---|---|
| 6 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |