Guys Can some one help me to create rules for allowing only smtp traffic from exchange server( inside) to message lab server ( outside) in asa firewall Version 8.3.1. Your earliest response would be appreciated.Thanksselva
Guys Can some one help me to create rules for allowing only smtp traffic from exchange server( inside) to message lab server ( outside) in asa firewall Version 8.3.1. Your earliest response would be appreciated.Thanksselva
Hi,We currently have a remote site connected over a site to site VPN to a PIX 515e at our head office. We also have a client to site VPN that also terminates at the same PIX on the same outside interface.We are in the process of testing the Cisco IP ...
Hello,We're using AIP-SSM-40, Version 7.0(2)E4.We send traffic from all interfaces to the IPS. When we test it with sigID 2004, we don't have any alarm.the configuration on the ASA is as follow :access-list inside_mpc extended permit ip any anyclass-...
Hello,I have two strange problem, please help me for success.static (DMZ,outside) 82.X.X.X 10.1.1.1 netmask 255.255.255.255access-list outside extended permit tcp any object-group WEB-SERVERS eq www access-list outside extended permit tcp any object...
Hi,I cannot SSH to a 5510, but I can ASDM to it with full privileges and make changes.The message is password authentication failed, but it's the same authentication I used to ASDM. I use passowrd manager, so it's not a typo.This is version 8.2(2). W...
Hi guys, When I go to the download ASA software most of them are ED releases, through I do see 3 interim release versions. Why are there no General release (GD) versions (in the 8.x.x code path)? Or are ED or Interim releases considered stable?TIA
Hi AllI am facing a strange issue with FWSM firewall rules and need some help on that.On this firewall, we have logging enabled to a log all denies for blocked ports. . This is covered in the last deny statement with port object-group as shown below....
Hello Members,i have installed a IPS Module on a router. Unfortunately the interface i use to access the router is in a VRF and i can't access the service module in this scenario. Here is the router config.interface IDS-Sensor1/0 ip vrf forwarding CE...
The 5550 is rate at 1.2 Gbps. But that througput is split between the 2 interface busses right? Actual throughput is 600 Mbps for slot 0, and another 600 Mbps for slot 1?
Hello,is there any plan/roadmap/reference for ipv6 support for dynamic routing protocols for ASA family?ThanksREgardsIvica
Hi,I was hoping someone could help me with a rule on an ASA 5510.access-list inside_access_in extended permit ip any interface OutsideThe idea is to simply deny access to any other network, but allow access to the Outside Interface for Internet conne...
Hi,We have a pair of ASA 5510's which we cant quite get to work properly when they go live. The problem is that we cant work out whats wrong with them until they are put into the production enviroment. Is there any software we can use to virtualise ...
Dear friends,There is a requirement for a wireless guest subnet to be policed to 600 kbps while sending traffic to Internet.The wireless guest subnet is 172.20.50.0/24 and is connected to inside interface of ASA.A point to note is that this subnet is...
Hello everyone!How do I configure my ASA to pass through a GRE tunnel encrypted with IPSEC? By default it fails!//Rulif
Hi all,can i do this with the ASA5505?i plan to use the Lease Line only for VPN Traffic and the PPPOE Line for Internet Traffic.Configinterface Vlan1nameif insidesecurity-level 100ip address 172.20.1.1 255.255.255.0 !interface Vlan2nameif outsidesec...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-19-2024 09:48 AM | ||
08-19-2024 03:53 AM | ||
08-14-2024 08:06 AM | ||
08-08-2024 06:44 PM | ||
08-08-2024 06:24 AM |
User | Count |
---|---|
9 | |
7 | |
4 | |
3 | |
2 |