Dear All Experts,I have configured Trend Micro InterScan for Cisco CSC SSM 6.3.1172.0I have blocked some actives. I have applied Time Allotment on Schedule but it is still blocking.any SolutionRegardsIA
Hi,We are in the process of building a new DC and would like to know which is the recommended version of code to run on the following:Firewall Services ModuleCisco ASA5580, 5550, 5520ACE moduleAny help much appreciated.Many Thanks,Matt Smith.
folksi'm looking for a basic multicast configuarion guide and troubleshooting/verification for 8.2 ASAcan anyone point in the right direction?thanks to anyone taking the time to reply
In English:I have 2 PIX 525, which one of them, step and active failover mode the other PIX 525, leaving this off, do not know what happened may have been a power outage, but in any case I can turn it back on? And the other question I have is if I ca...
Howdy,I'm aware that IPSEC tunnels are not supported in multi-context ASAs. Is the same true with setting up Cisco Client VPN? Any feedback and maybe a link to documentation would be greatly appreciated.
HiI need to fullfill the below configuration which is working fine on my actual D-Link Netdefend firewall.We have a range of IP assign by our ISP : 194.250.47.128/29194.250.47.129 is the firewall IP and 134 the isp gateway.We have 4 interfaces- The l...
Hi allI have an ASA 5520 with 2GByte RAM running Software Version 8.2(4)4.As soon as I enable outside interface Gi0/0 I get the following error message on the console every now and then:(set_exptime) Timer not a leaf 0x714644dc. Traceback: 0x805e4b3 ...
Hello guys,I'm running a couple of 5520 (with failover configuration) and fw 8.3.1. Everything worked fine until I try to upgrade firewall to new fw version: 8.4.1 .When I try to upload new firrmware or asdm image, ASA, the appliance reboots during ...
Hi All,Would like your suggestion regarding the setup. Its a streaming video servers behind the firewall with aip-ssm module with 2 servers and 10 cctv cameras and people are going to access those camera on their ipad through internet.Now as per the ...
Does anyone know if I am running ASA 8.3 (which runs as NAT0 by default - NAT is turned off) with REAL IP addresses if I have to still configure an OBJECT with NAT to allow traffic from a lower level interface (OUTSIDE) to a higher level Interface (I...
Currently Being ModeratedRegarding security issueHi All,One of my client hosted three FTP servers in a datacenter environment. Out of three servers one is a backup FTP server, if the primary FTP server is failed the users can access the back up serv...
Here's what I see when I do a show ver in console:Hardware: ASA5505, 210 MB RAM, CPU Geode 500 MHzInternal ATA Compact Flash, 128MBBIOS Flash M50FW080 @ 0xffe00000, 1024KBThat 210MB doesn't seem right to me... Anyone ever see that before?thanks,Chr...
I have a Pix 515, and a question about firewall rules/access lists.I have recently created a new VPN group, and IP Pool.I created a firewall rule that grants access via TCP to a specific IP address from this firewall. However, when I test the VPN fr...
Within a workgroup environment we have four large drives, statically assigned and all accessbile via VPN. Our FW is a Cisco ASA-5505. Where within the ASA-5505 GUI can one of these drives be made inaccessible via VPN?Many thanks!
Hello Everyone,I've two Cisco ASA 5550 firewall. I'm don't have much knowlege on configuring this kind of firewall. I need help on configuring these firewall for simple NAT. I have 3 public IP address. I would like to allow server's inside of the fir...
