HIplz help me with the follwoing1) i have a application sever on a dmz and i want to implement DDOS / DOS attack prevention on asa. what are best practises in order to accomplish this.2) what is the difference between a CSC and IPS modules. can i a...
Hello folks,It has been quite a challenge to find any relevant and good information shedding the light on how to integrate Cisco Security Manager 4.0.1 and ACS 5.x to authenticate and authorize CSM users. The available guide implies that all the inte...
HiHope someone can help, I have just installed CSM 3.2.2 and added many multiple firewalls to the database, I have not created any overall policies yet. Once these additions were made I could see over 500 changes that CSM wanted to make in the Activi...
Does anyone know if CSM 4.0 SP1 is compatable with ASA 8.4.1, released yesterday? The compatability doc (below) talks about minimum requirements and hints that it should work, but will be listed as 8.3 without support for new features. I'm just fig...
I'm running CSM 4.0.1 and followed the instructions on how to use CSM to update an ASA5540 filewall through AUS. I created a policy in CSM with the AUS IP address and credentials and chose 'Device' to deploy to.On page 1-3 of "Getting Started with AU...
Hi all, I have a server for public access in a DMZ, let's say DMZ10 and the IP for this server is 10.2.3.1. This local IP is natted to a public IP for outside. Packet tracer from in the ASDM shows that the packets get to the host;however, the...
Hi,I've just setup my first AnyConnect remote acccess vpn on a 5505 running 8.4(1). Everything works except I'm not getting a default gateway for my remote access vpn connection.I can't see where in the profile to set that up. Can someone point me to...
Hi,I have one ASA 5510 FW with AIP-SSM20 additional IPS module and security plus license. I noticed that this IPS module come with Virus/Worms/Trojans signature configuration . ( Pls.refer to attach pic ). I'd like to know how do I receive the servic...
So I am doing a project for my capstone IT course in college and I am stuck on a simple problem that I can find no help with. I was given an old PIX 501 firewall that noone remembered the password to. So I searched around and found a tutorial on this...
Is there any gotcha upgrading from 8.0(5) to 8.3(2)? Is it safe? Does all the commands in 8.3(2) backward compatiable with 8.0(5)?
Don't worry this isn't another load balancing question. I know that is not possible.But I have 2 ISPS and I would like to use 1 for my VPN tunnels and 1 for my internet.Right now I just have my last default gateway as going ISP1Interface 0.0.0.0 ...
I have one remote ASA that gets outside IP Address from DHCP, Is there any way to pass one of the outside DNS servers to be used as DNS for inside client getting DHCP address?
We had 2 License CSMPR-LIC-50 in Service and under SAS Contract with the needed S/N.Then we decided to merge these Licenses into CSMPR-LIC-100 for Cost issues.e anThe Licensing Team has sent the new License and we have it now in Service.Unfortunately...
Im trying to install CSM 4.01 on a windows 2008 r2 server 64 bit and getting a message that its not a supported os. Does it have to be the non r2 version of 2008?Thanksjeff
Hello, I'm working on a IPS design in a fully redundant DC that is almost impossible to force symmetrical flows. My question is when using assymetric mode for TCP reassembly - what exactly is lost? Below is the list I've come up with so far:1. TCP...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-10-2026 08:58 AM | ||
| 08-10-2026 02:48 AM | ||
| 07-22-2026 05:00 AM | ||
| 07-16-2026 06:39 AM | ||
| 07-15-2026 08:48 AM |
| User | Count |
|---|---|
| 3 | |
| 2 | |
| 1 | |
| 1 | |
| 1 |
