Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Showing results for 
Search instead for 
Did you mean: 
cancel

“Join

 
Labels

Forum Posts

when i telnet pix 7.0 from switch,i execute show run command.the information display half then stop.i must telnet again.but ping pix is normal.Is there something wrong?any help will be preciate.

wanglei by Level 1
  • 357 Views
  • 1 replies
  • 0 Helpful votes

Hi,I'm deploying IPS 4255 (5.0.4) at my customer site. I put the IPS between the internet router and firewall.Gi0/2 connected to firewall and Gi0/3 connected to router. Is it correct setup?We use default signature configuration.After deployed the use...

jcin by Level 1
  • 574 Views
  • 3 replies
  • 0 Helpful votes

I have two concerns regarding Cisco NAC.Will it work for Cisco customers running something else than Microsoft on their clients?Why does Cisco not develop NAC towards LDAP instead of AD?As far as I see it this whole NAC thing is just a big Microsoft-...

Is there any way to set JUST the signatures to default in 5.x? I tried doing a select all->default from the GUI but it eventually just times out with some rdep error. I also just tried doing it from the CLI using :(config)# default service signatur...

mhellman by Level 7
  • 557 Views
  • 4 replies
  • 0 Helpful votes

I have 12 IDSM2 and 4 IDS 4235 managed through VMS, I configured automatic download of signature updates but I notice that S189 was missed. Is it possible to apply the last Service Pack 4.1.5 from VMS? If yes do I simply have to download the file in ...

I am trying to put the IDS-K9-patch-4.1-4g patch on a couple of 4215's and every time I run the upgrade command it times out and fails with a zero length file on teh IDS. I have also tried to manually (from service account) move the patch to the sens...

mike by Level 1
  • 522 Views
  • 3 replies
  • 0 Helpful votes

I've configured the management interface of a 5.x 4235 sensor to be 100Mbit/full. It is still HALF duplex according to dmesg output and I am still seeing collisions in proc/net/cisco/ge0_1.info. Does anybody know if setting this via the CLI actuall...

mhellman by Level 7
  • 891 Views
  • 6 replies
  • 0 Helpful votes

If I have an a Pix that support vlan can working fine this configuration with two subnet that have surf on internet with PAT ?thanksLorenzointerface ethernet0 autointerface ethernet1 100fullinterface ethernet1 vlan2 physicalinterface ethernet1 vlan3 ...

lformelli by Level 1
  • 411 Views
  • 3 replies
  • 0 Helpful votes

Is SMS2003 supported as a method of rolling out CSA Agents?I have an unusual situation where the CSA agent kit is not being successfully rolled out by SMS2003, when retrying the process, I receive a warning that the agent is already installed, even t...

igyte by Level 1
  • 432 Views
  • 1 replies
  • 0 Helpful votes

I recently added a 4215 to VMS for management. The 4215 has s172 on it - which I have been trying to upgrade with no success. I am trying to push out s188 to it before I upgrade it to the newest service pack, etc. The problem that I am having is that...

soc by Level 1
  • 561 Views
  • 2 replies
  • 0 Helpful votes

Let’s be real -- the IDS documentation is miserable. It goes on endlessly without stated objectives and many of the screenshots are messed up. Ideally there should be a bunch of field notices that explain specific tasks. For instance, how to connect ...

brymiller by Level 1
  • 670 Views
  • 2 replies
  • 0 Helpful votes

We have a VPN 3K Concentrator. The users would like to access Microsoft Outlook client instead of webmail through VPN. Do you have any suggestions on where I would start?Thanks.

Review Cisco Networking for a $25 gift card