Is it possible to set a priority to traffic on the pix either by IP or protocol? And if so is this possible through VPN? I have a video conferencing traffic I would like set priority for. Thanks
Is it possible to set a priority to traffic on the pix either by IP or protocol? And if so is this possible through VPN? I have a video conferencing traffic I would like set priority for. Thanks
We need to allow telnet access to a server on the internal interface of one of our PIX 501s from several workstations on the outside interface's network.I can ping the 10.0.xxx.100 address without a problem, but I can't telnet. What am I missing?The...
I'm wanting to separate my switchports logically with VLANs and I'm wondering what my configuration should be.For each interface that I want to communicate I will run the below command in interface configuration mode.switchport access vlan 7I will do...
I have installed a Linkproof to do load balancing, behind that i have a fireproof with 2 cisco pix 515e, my vpn clients loose conectivity to the internal network and the only way that it gets fixed is by doing a reload on the pixes. Has anybody worke...
I have a PIX515E running 6 interfaces, I have a DMZ interface with a Server running IPSwitches WS_FTP Server on it. I have a Static NAT from the outside to a Public IP address. The FTP Server is truely set up on a private IP address on the DMZ inter...
Is the IP protocol version 6 supported in Cisco Pix 515 UR ?If yes, is also IPv6 support in Cisco 515UR+FO4 ? (it it possible to make also IPv6 with the FO4 ethernet extension?)
How can I open a port on a Pix 501 ? I tried to add a access-list with a port number. After that, I tested it with a port scanner and the port is not open. I thought that adding an access-list will open the port.Thanks !
I am having an issue where all wanted traffic can get in (Webpages, DNS, SMTP, etc.) but no machine from the inside can get out....even with a ping.I attached my config,When I try to ping to the outside from inside, I get this error logged...305006: ...
Is there a way to only send the following syslog message to my syslog server:syslog 304001I just want to send that syslog...nothing else...I remember seeing something around but just wanted to verify.Thanks
hi can I have 2 default routes in a pix?route outside 0 0 1.1.1.1 1route outside 0.0 1.2.3.4 15if connection 1 dies, the use the route 2... thanks.
Hi,Has anybody installed CSA on Solaris 9.0?If yes, are there any special considerations?
how I can obtain the IDS signature update file
I can't get our PIX to accept inbound traffic. I'm a Cisco newbie, and so using the PDM to configure the hosts, access rules, and translations.Everything behind the PIX works, as far as hosts externally resolving with the correct ips, having the abil...
I am trying to use a program WinSCP throught a pix 515. The application uses port 22 which is SSH so is kind of FTP over SSH. The problem I have is how do I enable this, do I uses fixup ftp on port 22? will the firewall see ftp traffic or SSH encrypt...
Hi all ,I config the acl in my PIX now , how can i know no another port is open ? have any software can ping 1-65536 port status?pls advise , thxStanley
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-02-2024 09:17 AM | ||
10-02-2024 09:13 AM | ||
09-30-2024 06:08 PM | ||
09-30-2024 09:44 AM | ||
09-25-2024 01:43 AM |
User | Count |
---|---|
11 | |
11 | |
7 | |
4 | |
4 |