Network Security

I'm trying to set up a tunnel between a branch office and the main office of a business. I can get the tunnel up and running and I can get the computers to ping each other as long as they are on the 192.168.1.0 or 192.168.2.0 networks. However, I can...

Hi,Can anyone tell me, witch license need I buy, to receive all the IPS signatureupdates and upgrades for IPS in ASA?Thanks!

Does PIX support supernetting? For example, can I configure a PIX interface as 192.168.0.0 255.255.252.0? I currently have 192.168.0.0/24 configured. But I need a larger range, and am hoping to change it to 192.168.0.0/22. My PIX OS is 6.3(1).Thank y...

I am a network consultant with a client who has a PIX 506e with Ethernet 0 & 1 both plugged into a Cisco Catalyst 2950 switch which also has private IP LAN clients on the same switch. My VPN is still working to another office with this config, but I ...

Since we started using MARS, I'm paying more attention to our syslogs, and on our Pix running 6.3.4, I'm starting to see a lot of the following syslog messages:%PIX-6-110001: No route to x.x.x.x from y.y.y.yThe IP addresses vary, but x.x.x.x is alway...

Hi, I have a PIX 515E connected to a 3725 router (Crossover) and my VPN 3000 sitting on my DMZ (NAT). When i look at my VPN tunnel, it shows as being up with it's peer. But i am unable to get traffic across the tunnel. I can do a trace route inside m...

Is it possible to NAT the inside source address where the desired NATed source IP is on an inside subnet?For example, can the source inside IP 1.1.1.1, appear as 1.1.1.2 on the outside, for an inside subnet of 1.1.1.0/24 ?static (inside,outside) 1.1....

I have a PIX 515E Restristed Lic.I have 3 int., 2 Otside and one Inside. Of the 2 Outside int, 1 is for a T1 and the other for DSL. Now, I have over 100 users. I want some of them to be directed to the int with T1 connection to the Internet and the r...

Please advise! I'm trying to push a signature update to a Cisco 4210. In troubleshooting I have logged in with the service account and found that after running the ./cids status command, the following message is displayed "mainApp dead but pid file e...

How do you test a IOS IPS setup on a routers external interface checking inbound data is working.I have set it to notify via syslog (ip ips notify log) and i know the syslog is working as an ACL is also set to log to syslog and this is showing result...

This is my first attempt to use PIX. I understood from my reading the PIX would allow traffice from the inside to outside by default. Is that correct? I have been unsuccessful to even get a ping to work. Telnet will not work either. Attached is a dia...

Hello,how can I verify that a pix is actively sending DPD 's and these DPD's are understood by the peer in debug modus ?Thanks for helpKind RegardsM. Koenig

Hi there, I have a PIX515E with 6.3(4) and a vpngroup running on it. This vpngroup is allowed to connect to one of our internal networks only and has been runing great. Now, I need to create another vpngroup so that this second group not only can con...

I was wondering how we'd do this. We have a sip phone that is natted 1-to-many behind a pix 515E running 5.4 pix code. We then have a sip server hooked up on the public ip side of the pix. The phone registers fine with the sip server and can even mak...