Network Security

Hi all, I got the problem , when i change A ISP (old) to B ISP (new), after that the internet connection is fail , here are change the running config information as below:1.IP address outside2.Global3.Route 0.0.0.0 0.0.0.0 x.x.x.xTesting before :If i...

I've tried several forum suggestions, PDM & command line changes to no avail. I have 1 Small Business Server behind a PIX 501 & I need to forward 5-6 ports (web, smtp, pptp, ftp, termsvcs, dns)to the SBS (192.168.10.11). The 1 public IP is the WAN ...

Hi experts,I'm using IE configured with proxy (the proxy's IP is public IP address). If my LAN is directly connected to a router (running RFC1483 bridging), I can get my address bridged and then connect to the internet.But, after I use PIX:LAN (192.1...

I would like to configure my pixs to only fail-over on only the interfaces I want.

Hi I have 2x 515E firewalls, one active and 2nd as failover. I have PIX-515-SW-R-UR= on active FW. and PIX-515-SW-FO on failover FW. Now my question is as follows,a. Will PIX-515-SW-FO license support all features as PIX-515-SW-R-UR= unrestricted fea...

Hi...I have a VPN 3005 concentrator that seems to work fine, that supports both incoming VPN remote access clients (using the Cisco client), as well as LAN-to-LAN tunnels elsewhere. Both seem to work fine, but I have a need to have some RA clients c...

Dear all,I want to open all ports for outbond traffic and open all ports for inbond traffic in my PIX 525. So I use this command :access-list 1 permit any anyaccess-list 2 deny any anyaccess-group 2 in interface outsideaccess-group 1 in interface ins...

When I log in with VPN, the Bongo icon turns yellow after about 30 seconds. I get the following message: Secure VPN connection terminated locally by the client. Reason: Lost contact with the security gateway. Check your network connection. After the ...

please help...ok..i have a gateway smtp server on my dmz..well trying to anyways, but i need to see what im missing here is my statics...121.161.99.70 is what my MX record is pointing to so this needs to be my DMZ, also 1.153 is my exchange which i n...

please help...ok..i have a gateway smtp server on my dmz..well trying to anyways, but i need to see what im missing here is my statics...121.161.99.70 is what my MX record is pointing to so this needs to be my DMZ, also 1.153 is my exchange which i n...

I had to set up my PIX for port redirection using static commands. I have it working, but had a question on whether port ranges can be configured for this. I have the ACL defined to allow the 120 ports in the outside interface. I tried to find a s...

I just added smtp commands to my PIX with an exhcange server behind it. Originally I tried testing this by doing a telnet from a remote PC. telent 24.x.x.x smtp to see if it would go through. The response I got was an encrypted/jumbled message lik...

I have an exsisting tunnel between a PIX and a 3005. How to make all traffic go through the tunnel. Right now port 80 traffic does not go through the tunnel. I wasnt to force all traffice from the remote site through the tunnel.

MS KB article # 158623 speaks to 5 static port numbers: 389,522,1503,1720, and 1731. And two dynamic port settings. How do I configure my PIX to pickup these dynamic ports?

Can the PIX only filter by IP address without the help of a 3rd party product ? For example, if I want to put a filter/access-list rule in place to prevent access to www.pornsite.com, but allow access to www.business_content.com, this does not seem p...