Network Security

I have a pair of PIX-535's that I've recently inherited at a new position. The OS version is different between the two. I'd like to upgrade the OS on the failover unit, but cannot access the console port. Nothing is displayed on my session. Is t...

Hi, I have a problem with my cisco PIX firewall 506E. I just implanted it into my network...but the pix can't ping anything from the outside except the translated address of another firewall of our servers...in other words…it can see the ne...

I am running a 3005 and would like VPN clients to not use split tunneling and run all traffic, local LAN and Internet, through the VPN tunnel. Currently, I can get the local LAN traffic to work, but no Internet traffic is passing.On the 3005 I have ...

Dear All,I have a bit of a problem with one site that is running NAT-T. The problem is that it is never komming up.It seams like it is ok, and it has detekted that it need NAT-T, but then it delets IT.here is my trace:AGENT-REK1# sh debugAGENT-REK1# ...

Going to upgrade to 6.3 but I wanted to save the old image to tftp server firstcopy flash tftp doesn't workCiscoPIX515E# sh verCisco PIX Firewall Version 6.2(2)Cisco PIX Device Manager Version 2.1(1)CiscoPIX515E# copy Not enough arguments.Usage: cop...

my IDS is 4.0 with S37+IDM 4.0my pix is 6.2(2)When I configure shuning on my pix via telnet on IDM Web pagebut it seems can not telnet the pix to do shuning (inside interface)Why ?(I have saw the post that pix 6.2(1) can not use telnet Do I need to ...

Hy I have a problem with 2 pix 525 in lan statefull failover the software version is 6.2.2:Sometimes when I issue a "no debug ....... command from an ssh session,the active pix reboot and the secondary pix take control.In the syslog with trap level w...

Folks,I wrote a small program to parse the configuration. I am looking for a sample configuration of a Edge Router ( preferably 7200 ) having lots of configuration data including VPN , Martini Tunnel etc. I need to test my parser. Any help will be gr...

whenever I access the web site which is behind the Pix firewalls, the speed is realy slow.i bypassed the firewall and accessed the same site and it's fast!.I checked my settings and made sure all the connected devices arerunning at 100 and full dupl...

I want to have 2 wan links connected to a Cs 2611 (wic-2t) and run gre+ipsec tunnels (half remote tunnels to Isp1, the other half to isp2). I also want Eigrp for automatic convergence (eg primary tunnel to isp A, secondary to ispB).Any similar workin...

I have tried to install CD one second edition with RME 3.1 and have run into trouble. CD one installs fine, however after I install RME 3.1 I get a message, essentialsdbmonitor cannot connect to 'rmedb' Database. This stops me from viewing running ...

How can i forward one ip 155.55.134.25 to an internal ip 192.168.150.251. The router is running nat and i have created the ip nat source static OUT_IP IN_IP command, but when attempting to ping the IP from outside the device i can not get any acknold...

Documents don’t jive. Looking for correct answer.Starting at this link (http://www.cisco.com/warp/customer/cc/pd/fw/sqfw500/index.shtml) the specs for the 501 are:Outside Interface: “one 10Base-T interface”Throughput: “provides up to 10 Mbps of fire...

Hi,I want to configure SNMP Traps, whenever a User logins\Telnet to the Router.However i am somehow unable to find a way, how to ONLY enable this functionality.I don't wan to receieve any other traps, except when a User Logins to the router.Which SNM...

1. I am trying to shun a host for 1 minute when a specific alarm is triggered. Shunning works O.K. but after 1 minute the entry in Block Host menu on IDS sensor dissappears but there's still a shun command on PIX. In other words it seems that the sen...