Optics and Optical Networking

Resolved! Increasing VCAT size on CE-1000-4

Hi all, here is my delima. I have a CE-1000-4 cards with three provisioned ckts . Two provisioned as STS-1-2v, one provisioned as an STS-1-10v, Looking at the current provisioning, I should be able to increase the STS-1 count on one of the STS-...

Resolved! ONS 15454 DWDM

Hello,I am still pretty new to the ONS product line, but have a reasonable understanding of the DWDM technology. I am looking to run two point to point dark fiber links between two colos within about 3KM of one another. Ideally, I would like to suppo...

DOM commands for cisco 3560G switch

Hello. We have many cisco 3560G switches running 12.2(46)SE. Several of the switches are on cwdm fiber links. We would like to be able to query the SFP's to see what their optical values are. I am told by a cisco optical person...

Unable to configure ML-MR Card

I have an ML-MR 10 card. I cannot figure out how to get the ONS 15454 to recognize it. I insert the card. I then the card and right click. I go to Ethernet and there is not an ML-MR Card. There is a ML1000 and an ML1000T. I really am not sure...

Resolved! Veriyfing Power Levels via CTC

Hello all,I am looking to find out the different ways to check power levels of the different wavelengths using CTC. When I cable up the different optics on the CE devices, I want to be able to log into the CTC and check to make sure the power levels...

Resolved! WS-G5484

Hi ,We have a couple of these SPF transceivers which we have not use for a a while ie a year or two.Now we want to use them but how do we test it to see if it is still working ???ThanksQLE

How To Connect To 1545 via CLI.

I am in despeate need of some assitance in connectng to my 1545. We upgraded our software and now the lights on the 1545 just blink. I do not know if I can connet to this via the rs232 connection or not. I am not sure if somehow I can get the ...

Resolved! Unable to provision POS links in CTC to ML1000-2 cards

We have a 4 node ONS15454 MSPP UPSR ring running 8.5.4 software. We are running the usual mix of DS1 and DS3 circuits, however I'm trying to standup some ML1000-2 cards to be used to transport some Ethernet circuits across the rin...

Regarding COPY-RFILE TL1command in 15454

According to the TL1 document for 15454, COPY-RFile command denotes that FTP timeout is 30seconds and it is not configurable. I have the following questions on this.Is the timeout for creating a connection to the FTP server or for the total command e...

sg200-26 problem with MGBSX1

Hi everyboby,in the office we have 4 switches SG200-26 all connected ones between them in fiber.Only one however it has problems with mini-gbic SFP transceiver, if inserted it doesn't ignite any red light.Can he depend on a hardware problem only or d...

Resolved! Testing fibre cables from a switch

Hi everyone,I have two new Cisco switches connected to each other with a fibre cable.Does anyone know any CLI commands to test the fibre cable from any of the two switches?(I know there is the command "test cable-diagnostics ... etc". But, this only...

Read full EEPROM of SFP+ (3750-X)

Dear all,we want to read the full EEPROM information of a SFP+ which is within a C3KX-NM-10G network module within our Cisco Catalyst 3750-X switch. IOS is 15.0(1)SE.I just found the "show idprom interface tengigabitethernet x/x/x detail" command, bu...

Does 1000BASE-LX SFP work with 1000BASE-LH GBIC?

Hi,I am sorry if this topic has been up before. I am rather short on time so I need to get this cleared asap. I wonder if the 1000BASE-LX work with the 1000BASE-LH GBIC? Unfortuneatly the devices are remote so I don't have anything more to go on than...

Diagnostic Monitoring is not implemented

Hi All, We are trying to find the reason and solution for the below problem. We are tring to perform the below command and get the below message.router#show interfaces gigabitEthernet 5/1 transceiver Diagnostic Monitoring is not implemented.The modu...

Resolved! Can SFP GLC-GE-100FX work with WS-C2960S-48LPS-L?

Hi all :The whole picture is as below:One side of fiber port from Cisco AP 1240AG is converted to Multimode Fiber 100MBit so that it to travel long distance to 1G port of WS-C2960S-48LPS-L. My question here is whether the SFP of model GLC-GE-100FX ca...

Optics and Optical Networking

Forum Posts

Resolved! Increasing VCAT size on CE-1000-4

Resolved! ONS 15454 DWDM

DOM commands for cisco 3560G switch

Unable to configure ML-MR Card

Resolved! Veriyfing Power Levels via CTC

Resolved! WS-G5484

How To Connect To 1545 via CLI.

Resolved! Unable to provision POS links in CTC to ML1000-2 cards

Regarding COPY-RFILE TL1command in 15454

sg200-26 problem with MGBSX1

Resolved! Testing fibre cables from a switch

Read full EEPROM of SFP+ (3750-X)

Does 1000BASE-LX SFP work with 1000BASE-LH GBIC?

Diagnostic Monitoring is not implemented

Resolved! Can SFP GLC-GE-100FX work with WS-C2960S-48LPS-L?

Fast laser diode at 850nm, single-mode coupled

MTP vs MPO cable availability from Cisco

The WSON feature does not work well

Degree Move - Want to Delete/Rebuild OCHNCs Via TL1

NCS2006 shelf menu

C9400

1gb/s single mode single core SFP?

Can C8500-12X router support SFP-10G-SR SFPs

What Happens When You Configure duplex:auto/speed:1000?

Running SFP-10G-LR over all fiber links