Other Network Architecture Subjects

We have radius authenticating our remote users (PPP) and that works fine, we have specific group profiles on the radius and that determines what IP user gets and timeouts and so on, now I'm trying to inject route into the NAS using the ip:rout AV-pai...

RME3.5 on Sol 8--I'm not able to see any contracts under contrat connection. I have 5 contracts added to my CCO Profile and they appear under my profile when I go to CCO but not under RME-contract connection.

How do I get the 1720 to recognize the WIC-1DSU-56K4 for a DS0 64K circuit?line is supposedly a 64K circuit...have tried a WIC T1 CSU/DSU with 1 timeslot lmi=ansi...no joy...Carrier indicates that circuit is DS0, I have a WIC 1DSU 56K4 card, but the ...

I am having a heck of a time and I can not figure out why.Here is my setup2 2611's seperated by 2 netscreen firewalls.The Netscreen ip's are 192.168.100.1and 192.168.102.1These plug directly into the routersThe routers ip's are 192.168.100.253and 192...

Hi there,2 x 7206 OC3 lane modules. Lane clients Register with Les/Bus on Nortel Centillion 100. HSRP configured and working between Lane modules. However the Centillion supports dircetly connected Token Ring Devices.When I run a continuous Ping from...

Hi one of our C836 does not allow aC836#reload at 20:00No bootable image in flash. Load an image into flash and try again; eg. using "copy tftp://<server>/<file> flash:"Reload to ROM disallowed from a telnet line. Reload cancelled.though a image is...

Hello,I have configured the MWAM processors to support tacacs aaa when logging in via telnet to them I have it functional when telnetting to a defined mgmt ddress in the MWAM, but when using the 'session' command from the supervisor, 'Authorization f...

I was reading about how I could enable caller ID recept on My 3660 router.My users connect via NM16 modules thorugh POTS. the POTS service provider has enabled this feature on those lines.Must I have a voice module or other modules to recieve the num...

HiI have cat 6509 with redundent power supply and two sup1 modules WS-X6K-SUP1A-2GE.When one of my power supply went down, the switch stopped functing although it was still powered up with other power supply. Looking at console, everything looked fin...

I want to get the amount of usage of the 8 pri's that connects to my AS5300. I am using Cisco Work to push out update, could I get the stats thur Cisco Works that would tell me the number hits I am getting on each pri?

I have a new T1 circuit from AT&T that is not coming up. I coded it the same as our current MCI line.Do any of you all have the IOS setup for an AT&T line? I have a 2600 with a T1 WIC card, but other models would probably help.

hi allwht should be the nominal/max/min values ??this is the current values set.Playout-delay Nominal is set to 60 msPlayout-delay Maximum is set to 200 msPlayout-delay Minimum mode is set to default, value 40 mshow much we can configure or how much ...

In which IOS release is Bidir-PIM supported for the Catalyst C5407?Best RegardsAndrea CalligherNetwork Engineer

I am a CCNA student and I just bought 3 Cisco 801 routers on E-Bay.The version is 12.1My question is: Is there a possibility to make my router back-to-back on the Bri interface?With the 801 I also receive a alpha telecom inc ut620F adapter might it h...

Hi,Anyone on this forum had configured catalyst 4003 with 2 gigabit ports in L3 module? I wanted to use these 2 gigabit ports as my backbone connecting to catalyst 2950 gigabit ports. Unfornately, i can't configured correctly. I can see the peer swit...