Excuse me , Who can tell me where to find all cisco products' output electric power? Thanks
Excuse me , Who can tell me where to find all cisco products' output electric power? Thanks
We have two main sites connecting to a customer network through PIX 515s. The PIX 515s sit behind Cisco 2600s which are configured as GRE tunnels terminating at the customer Cisco router. The GRE tunnels are transmitting and receiving OSPF LSAs...
How a eui-64 ipv6 address is calculated if prefix length is longer or shorter than 64?
I am trying to configure an analog lease line to connect to a 2621 via an NM-8A/S. The modem is currently connected to a RedHat box on the remote side and a FreeBSD box on our side. I want to move from the FreeBSD box to the 2621. I need to use the f...
I am seeing a weird problem with Some IPs ona 2691 router (we have a DSL network on one interface) which plugs into a Cataylst switch (We do not manage this our DSL provider does)anyways I have a /24 on an ISL trunk If I ping 207.x.x.2 (from router,...
Hello to averyone,please help to solve not a difficult task which I don't not how to solve at the moment.So, there are two Cisco routers (one with BRI and another one with PRI interfaces) connected to ISDN network. I need to configure a DDR connectio...
Hi,I'm not able to set up a public IP address -got from ISP- to our Cisco 801 router.Please, let me know how to add the public IP to interface Ethernet0. I did these steps: config terminal no ip domain-lookup interface ethernet0 ip addres...
I have a Cisco 831 which I'm assuming has a missing IOS.When I power up the router instead of going through the normal POST; and for lack of a better term it's putting out a bunch of goble-di-goop..I am unable to type in any type of command using the...
I'm using ACS 3.2 and I configured ACS with a Windows Database as External User Database for users to authenticate.I selected the domain in W2K AD and the users groupsto map them with the Cisco Secure Groups.In the Default group, I put <no Access> fo...
Dear Sir,We have a hub and spoke WAN network with on central location and 7 remote locationAt central location we have LAN subnet as 192.168.1.XAt all remote location we have LAN subnet as 192.168.2.X, 192.168.3.X etc..We have a exchange server at ce...
Hi,eg i have a server with internal ip (inside - 10.10.10.10) and i wants clients to access using the ip (outside - 192.168.10.10)if i use NAT, can i use "ip nat inside source" or do i use "ip nat outside source"? Or both works?ThanksSteven
Hi..I thought I knew this stuff, but now am unsure! :(If someone could let me know if I'm on the right track and/or provide insight, it would be appreciated.I created the following extended ACL:access-list 105 deny ip 172.16.0.0 0.31.255.255 anyac...
I have 7 C2950T-24 10/100/1000 in my network, what is the best way to link them, Daisey chain or,run allswitches into one master switch using crossover cables, that is currently what I am doing, all ourserver are also in the same top switch.
Hi ppl,2 routers running eigrp, during their initial startup (after neighbor discovery)What will both routers send to each other? a topology table or a routing table?If is a topology table then both routers will contain each router's feasible success...
There is a problem, when I connect Catalysts 3550-24T to Extreme switch with 10-full and any port settings, the connection gives some number of CRC errors.but if replace catalyst 3550-24T with 3524, there is no CRC.firt i suspected the hardware fault...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
07-17-2024 06:07 AM | ||
05-29-2024 04:52 AM | ||
02-14-2024 04:00 AM |