I am in the process of implementing RSAC in my infrastructure. Has anybody implemented this and if so, how did it work out?
I am in the process of implementing RSAC in my infrastructure. Has anybody implemented this and if so, how did it work out?
I have an ADSL modem/ bridge that I have connected to a DSLAM and ATFX pvc going to a serial connection on a 3640. I cannot get the two sides to talk. I've used a standard frame-relay subinterface and DLCI command and a simple ATFX con. Anyone eve...
CW2k LMS 2.2 IDUs 7.0, Win2k SP4.Are Cat6500 running Native IOS supported int UserTracking? Currently when I click on device for discovery, it said device not supported.
I am setting up CiscoWorks LMS in a new install. I have installed all the packages and updates, but the ANI server will not run. The ANI server log display the following:MESSAGE AniMain: Properties will be read from C:\PROGRA~1\CSCOpx\campus\etc\cwsi...
Could you advice on an architecture to achieve a site access redunduncy using routers with HSRP. Assumed that you have at least 2 phisical access links and one of the links sometimes gets full of errors, but don't fail completely. Is it a way to set ...
Can someone point me to the web page the defines what all the various Software Feature Sets include? I am referring to "IP", "IP Plus", "Enterprise", "Enterprise Plus" etc etc etc. Thanks.
HII need to set VLAN ID over the number 1023. For example "2500" or "4000". Could you tell me this can be done in Catalyst 8540?ThanksEsteban
Hello,There is a possibility so that a machine connect with network can see the whole of traffic which circulate in the vlan to which it be attach(broadcast, unicast, multicast).And if there is some tool freewere which can be use for this goal.
I have an issue with printers connected to a newly placed Catalyst 4006 with SUP II. We also have PC's and IP Phones connected to this same switch and they have no issue getting DHCP to work. Printers however that are set to use BOOTP/DHCP are not ...
Hello All:Is there anyway to filter client VPN access through a 1721 router by client MAC address. We have a handful of users who require VPN access and would like to tighten it up a bit by allowing only specified MAC addresses. If this is possible, ...
Hi,We have a lease line (WAN router) that connect to the internet. is it possible to have an isdn router to backup the primary link in case the WAN router fails?If that is possible, any examples or configuration notes on how to configure the isdn rou...
Can my cisco 3725 router become a NTP server for my MS Windows domain controler? I configured with no problems the router to sync to a public NTP server, but how do I get my router to then become a NTP server? Is that posible?
Hi, is there any way to manipulate the P-bit which is used for conversion from LSA Type 7 to Type 5's on ASBR's. Just curious and not sure in what scenario it would be used so if someone could give an example of when would this be needed if ever that...
I have installed two Catalyst 4507R connected on trunk and I have configured an a Vlan 3 for IP telephony and an a Vlan 2 for dates.The interface ports at begin were configured all:switchport access vlan 2 switchport voice vlan 3 qos trust device cis...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM | ||
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM |
User | Count |
---|---|
3 | |
1 | |
1 | |
1 | |
1 |