Other Network Architecture Subjects

Hi I having problems configuring this switch. I would like to get some information about how I can configure Vlans over ISL or IEEE.1Q. I add some specifications of the siwtch.If you need any hint just ask me and I will be more specific.Do you have s...

Are these wrong vlan IP ranges or are they correct:1st vlan id: 10.4.0.0 /20• 1st valid IP address: 10.4.0.1 /20• Last valid Ip address: 10.4.15.254 /20• Broadcast: 10.4.15.255 /202nd vlan id: 10.4.16.0 /20• 1st valid IP address: 10.4.16.1 /20• Last ...

Running CWLMS 2.2 on SolarisRME 3.5CM3.3Using a local hosts file, approx. 190 entries. All but 16 devices are discovered with the proper name resolution. Those for which name resolution via the hosts table does not work can be pinged from the serve...

The system and port LED's are amber. Ports 9-12 are experiencing this issue. These are unused ports that have been administratively taken down.I get the following output when I used the sh post command:POST FAILED: FastEthernet0/9 failed front-end lo...

I occasionally receive this error message. %SPANTREE-5-PORTDEL_FAILNOTFOUND: on different 6000 switches.The results from the Error Message Decoder indicatethat this is for debugging purposes. I'm not running any debugging tasks on these switches. Wha...

Hi,Is is possible tu use another database than Sybase (e.g Oracle, SQL Server) with VMS ? I saw it was possible to use SQL Server 2000 with CSA MC, but I need to know for the other MC modules ?I thank you.Patrice

My switch went down twice this mroning, i was able to capture the following message004 Feb 20 11:35:07 EST -05:00 %SYS-4-P2_WARN: 1/Astro(6/1) - management request timed out.2004 Feb 20 11:35:08 EST -05:00 %SYS-4-P2_WARN: 1/Astro(2/6) - management re...

I can ping the WAN serial interface, no problem. But I got this error message fill out my log. Any idea??-Traceback= 80050734 80066B60 80026864 8002CC60 8002A860 8014C3B0 8012163C 80140EF8 80140EF8 801216FC 8009E910 8009E8D0 80125E7C 80122908 8000812...

Hi,I have a catalyst 2924-M-XL with IOS 11.2(8)SA5. I cannot use this catalyst for Trunking to other switch because the IOS is standard version. So, I am tried to upgrade with Enterprise version such as, IOS 12.0(5)SA5. After the upgrade, my catalyst...

Although port is set as follows:set port qos 6/5,6/27 trust trust-costhe sh qos info run 6/5 suggests that the runtime trust is actually untrusted:The qos trust type is set to trust-cos.Warning: Runtime trust type set to untrusted.Do I need to set th...

I want to use the IOS indicated in the system bootstrap.ROM: System Bootstrap, Version 12.1(3r)T2, RELEASE SOFTWARE (fc1)Here is the entire show versionCisco Internetwork Operating System Software IOS (tm) C2600 Software (C2600-I-M), Version 12.1(2),...

Hi All,I have a 7507 using RSP4+ which boots up OK, however, if I initiate a selftest from boot prompt, it gives me the following errors:==============================System Bootstrap, Version 12.0(10r)S1, RELEASE SOFTWARE (fc1)Copyright (c) 2000 by ...

Hi,I need to know what you can do in term of configuration of the IOS Firewall (access rules, CBAC, ...) with VMS in general and with the Router MC module in particular ?I thank you,Patrice

Hi all-I'm looking for a utility or such that will periodically check the network (via either CAM or ARP tables or something) for one or more specified MAC addresses, and generate an alert (email?) when one of them is located. I'm sure there must be ...