A while back I found a tool in Cisco's web site that would allow you to select a switch, enter in its modules and check the configuration for errors... Does any one have a link to that tool? I cannot for the life of me find it again...
A while back I found a tool in Cisco's web site that would allow you to select a switch, enter in its modules and check the configuration for errors... Does any one have a link to that tool? I cannot for the life of me find it again...
Our modem can only be put in a room where someone sleeps.The lights on our Cisco phone/internet modem are too bright. The lights are seeping out the vents. There is no other solution but to put the modem in a smaller cabinet.The cabinet is made out...
I installed NIC Drivers to a Standalone server, installed Teaming Protocol, Used enictool.exe to configure VIC Team (-m 4 (LACP)), but I need to understand what "connection" Load balancing method means. By default Connection is used, but there are op...
Hi Team, We are Using a asr903rsp1-universalk9_npe.03.11.01.S.154-1.S1-std Ios For cisco ASR 903, I want one Suggestion if I want to Upload/Copythe IOS from active to Standby Than what is the Procedure and the Standy controller is on rommon mode how ...
Hi Team, We are Using a asr903rsp1-universalk9_npe.03.11.01.S.154-1.S1-std Ios For cisco ASR 903, I want one Suggestion if I want to Upload/Copythe IOS from active to Standby Than what is the Procedure and the Standy controller is on rommon mode how ...
Hi therei have a serious problem in my network that i need an urgent solution fori have got an 2811 router and a 3560 Cisco catalyst switch the 2811 router has two interfaces (f0/0 & f0/1) f0/1 is connected to the Wan and f0/0 is connected to the 356...
Hi everyone,I have a Cisco 2911 (IOS ver 15.3(3)M) in our branch office and Cisco 7204VXR (IOS version 12.4(4)) in our headquarters. They should be connected to each other via IPsec Tunnel over EIGRP.On the Cisco 2911, I receive this from the log:Nov...
Hi All,Following is the mstat output taken from one of my multicast routers. Please refer the highlighted area. Is it means that there's a packet drop between dd.aa.net & ee.aa.net hops ?? #mstat xx.xx.xx.xxType escape sequence to abort.Mtrace from x...
Hello! I am currently a student at Devry for cisco training in network Comm. and I also work tech support for lenovo. Right now I am studying to get my A+ cert so I can get a better paying job as well as study for my CCENT than to my CCNA. My questio...
I am using BASP to setup NIC teaming on a Dell R720 server. My understanding is that both of the following teaming methods supports load balancing/sharing. ie: team with 2 NIC cards (1gbps each) I will get 2gbps throughput. Am I right?• Smart Load Ba...
Hi All, I'm a little confused about how to configure NTP on the nexus 7010. I have an admin VDC and four working VDCs. I read that you can only configure NTP on the admin VDC but the commands are also available on the other VDCs. As the admin VDC ...
Hi, Will C3KX-NM-10G support fiber and copper modules. Thanks & RegardsAathif
Hi,We need to have a modem with 4G LTE card that supports MTU size of more than 1500 bytes.Does anyone else struggeling with the same issue? Thanks Regards Hans Kristian GravdalTampnet A/S - Norway
Hi All,I have a Cisco 2851 with 2 HWICD-9ESW ( 18 ports ). According Cisco document http://www.cisco.com/c/en/us/products/collateral/routers/2600-series-multiservice-platforms/prod_qas0900aecd802a9470.html , I can only have 15 vlans [ but I have 18 p...
I want to automate copy custom backup configuration (custom-confg) to running-config at a reccuring date
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |