When the command states that the time must be the same on all devices on the specific network does that mean the ospf area or something else?
When the command states that the time must be the same on all devices on the specific network does that mean the ospf area or something else?
Anycast-RP with Auto-RPIs the cisco documentation correct?http://www.cisco.com/univercd/cc/td/doc/cisintwk/intsolns/mcst_sol/rps.htm#xtocid12http://www.cisco.com/en/US/tech/tk828/tk363/technologies_white_paper09186a00800d6b63.shtml#xtocid13You have t...
We have the new WSX-4148RJ(v3.1) module on our Cat4506 and we are using straight UTP cables link to CSS11150(v5.0). This works fine. However, when we switched to a older WSX-4148RJ (v2.3), it doesn't work unless we use cross cables.Looking at the ...
I 'm implementing multicast over cat 6509 , but I encounter a problem is very confused me .I enabled Ip multicast-routing and ip pim spare-mode ,igmp-snooping on a vlan interface . Then I test a multicast server .The video is always paused...
I have 3600 x.25 router. It is using for ATM based project. I have one network 192.168.3.234 which is connected to hub. This hub is connected to E0/1 of router.(192.168.3.1) This is working fine. From the router to ATM is connected to through se...
Hello Colleagues!Yesterday, I have upgrade IOS on my cisco 7400 and now have big problem with PXF and Netflow. When PXF is running Netflow isn't working! :(IOS (tm) 7400 Software (C7400-JS-M), Version 12.2(16)B, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1...
Just wanted to know if a cat6505 w/PFC2 can run MLS with an external 6506 w/PFC2 and MSFC2 like the cat 5000 could. The cat with the MSFC2 is running native IOS.
hi,i have a atm interface on which i do tag-switching because of mpls.!interface ATM2/0.100100 point-to-point description MPLSWELSPE01: PVC to MPLSRBGOPE03 (ATM2/0.100100) ip address x.x.x.xip ospf cost 50 ip ospf priority 100 pvc 100/100 cbr 8800 ...
Does anybody know when IOS 12.1(19)E for Catalyst 6509 will be available ?Thank you in advance
Three weeks ago I have upgraded one 6506 softwareCatOS 6.4(3) + IOS 12.1(13)E6. No problem!To use the GBIC-TX, jesterday I upgraded the same switch at the CATOS to 7.4(3).Then appears the problem that the module Multilayer not come online!2003 Jun 05...
HI,I have some network problems (high rate of broadcast and a big time of reply..)I need your help to monitor the network and if you know any free network analyser.thanks
I was handed a project to get a Linksys DSL router to communicate with a lan that has a Cisco 1725 router and a 2924 switch; the linksys wan port is plugged into the switch. The linksys supports only Rip v2 and so I turned this on for the 1720 (whi...
we experience problem with catalyste 4006 after updating os from 5.4(1) to 7.6(1) and replacing blade ( SLOT 5 who 8 port was broked)what we got since we did the replacement and the Update os is : disconnecting for 8 port ( Slot 3 port 1-8) Message...
i have 7206vxr router with dc power supply, can i replace the dc power supply with ac power supply in the same chasis.
All of my 350 series AP links on the topology map display a 100m segment between the switch and AP. This started after I enabled snmp on the AP's. Prior to enabling snmp, the links appeared as any normal link from a switchport sans the 100m segment...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
01-22-2025 07:00 AM | ||
12-30-2024 06:12 PM | ||
11-14-2024 09:33 AM | ||
10-24-2024 11:51 PM | ||
10-20-2024 10:52 PM |