Other Network Architecture Subjects

I'm using a NMS Korean product...and I'm trying to get mib of catalyst 2820 and everything is well done.but only one thing, collision counts, is not presented in my NMS.I can notify port utilization, link connectivity something like that...Catalyst 2...

Hello all. I just recently purchased a local director from a 3rd party network management company. I am hoping to find a little more documentation about setting this up. I have gone through the sites including Cisco's. Still I can't find much more th...

Hi, I am using 5300 access router. I configured following globle commands for snmp:snmp-server community <removed> ROsnmp-server community <removed> view v1default ROsnmp-server community <removed> ROsnmp-server trap-source FastEthernet0snmp-serv...

How do I configure this router to resolve DNS names of my internal network for users on the internet? I have a W2K DNS server in the internal network. (ip nr 10.0.0.1, router has 10.0.0.254)When I open port 53 it won't work even with PAT.Thanks

I now have a public IP space: 169.139.247.0/24, but rumor has it I'm shortly going to have only a /26. I moved all my public hosts into a 169.139.247.0/26 VLAN, then NATted the rest from a private 10. space. I wanted to just pick a single address f...

Say I have two 6509 as distribution switchs, and Vlan 100 as management vlan. I created Vlan 100 interface in MSFC-II. Do I have to create a standby group for this segment, so all the other switchs will point to the HSRP virtual IP as default gateway...

I am accessing the switch through 3 steps as follow:TELNET switch name (or IP address), Enter Login ID and Enter Password.How can do the 3 steps in 1? Is there any specific parameters where you can add the Login ID and password next to the switch na...

Hello.I would like to use virtual-template on 7513 for dial-in ISDN.I'm concern about getting to the limit of configurable interfaces on the machine, but I can not find the actual limit.Does someone know what is the total interfaces that can be confi...

SITE A (S0)----(64K DDN)---- (S0) SITE B (S1)----(512K FR)----(s0) SITE C (E0)SITE A:--------------------------------------------------------interface e0ip address 202.101.1.0 255.255.255.192interface s0ip address 202.101.224.2 255.255.255.252ip rou...

Hi !Our router defaults to NPE-175 whenever it doesn't recognize the installed NPE. Is it possible to define the NPE-type for the 7206 VXR manually ? I want to use NSE-1.If yes, then please let me know what command to use.Thanks.Regards,Fareeduddin A...

Hi .. can anybody let me know how i can find the bandwidth that's been utilised by differnet protocols say(http,pop3,ftp..etc).

Hi, I need to do the following...-to be able to receive a full e1 on a card on a 3600.-separate different slots into different subinterfaces-then, grab the slots asigned to one of the subinterfacesand 'hairpin' them to a serial interface (v.35).is t...

*Mar 2 15:41:18: %AMDP2_FE-5-EXCESSCOLL: Ethernet2/0 TDR=1, TRC=0when the message appear,the router will loss the packet.please hepl me!

Hi, I have a 2912XL-EN switch. I am trying to get a router that supports fast ethernet to do inter vlan routing and I was wondering if the 1720-21 would be a good low-cost solution. Also, does the 1720-21 support ISL encapsulation or only 802.1q. Wou...

My campus has a building that is around 2000ft. from the master swtich. The runs to the building are Multi-mode fiber. From looking at Cisco docs, I cannot do Gigabit ethernet over multi-mode fiber because the longest distance is 1800 ft. over MMF. ...