Other Network Architecture Subjects

I have recently applied traffic shapping to two routers.I have been doing a show que (interface) and am a little confused by what I am seeing.RXL505#sh que s1/0Output queue for Serial1/0 is 3/60 Packet 1, linktype: ip, length: 44, flags: 0x8 sourc...

From cisco/Understanding MTSP:The IST is the only spanning-tree instance that sends and receives BPDUs; all of the other spanning-tree instance information is contained in M-records, which are encapsulated within MSTP BPDUs. My questions:On which VLA...

Hi,I am having a problem getting unequal cost load balancing to work. I am using EIGRP and have variance set to 3. I have this mocked up in my home lab to duplicate the problem at work. Here is link to a crude picture of the setup. http://www.ger...

i am looking for an ios image for 1601R router -8mb RAM- , for 2 months but i cant get it .i cant get it from cco also .thanks

Is there a Cisco doc that explain the "cat6000-sup2cvk8.7-3-2.bin" what is the k8 means. How do I decide what ver of CatOS I use in my 6513 with 2 msfc.

Am having a hard time justifying $10K for the Sup IV enhanced IOS just to get EIGRP for routing between 5 VLANs. Will probably just use static routes.Questions if a decision is made in the future to spring for the software:1) Is it a normal TFTP pro...

I have a 7206 and a 3640 connected to each other via inverse-multiplexed T1s.The IMUX are Digital Link DL-3800s. I have 4 point-to-point T1s for a total of 6.122Mbps. Each router has a HSSI module installed.In one direction, moving data from the 72...

Are 1760 and 3700 routers supported in router MC ?//Bjorn

I have just upgraded my CiscoWorks to CD Five LMS 2.1 I thought that this would add my IOS 4006 SupIII switches as supported devices. However it seems that they are still not supported. I don't know what to do. I looked at the IDU 1.0 for CD 5 a...

Hi gents,I would like to know if this feature can help in LAN switching environment where stp loops occurs. In case of stp loop, the box may crash because of a too high utilization of the cpu. There is no feature where we can set a threshold for the...

when connecting to console port unable to detect the switch.hyperterminal not able to sense.wereas the switch can be sense accessed through telnet.is it a hardware problem or some thing with config.as seen on sh startup-config line con 0 transport i...

I have two sides interconnected by frame-relay point-to-point interface . On each side ,i use the static route point to the other side by using the command such as "ip route 192.168.0.0 255.255.255.0 10.0.0.1" command. In order to backup,i hav...

Is there a way to allow the transport of a 802.1q trunk connection on ports configured as access ports ? In other words on an existing switched environnement you define a vlan with access ports and you interconnect two other switches using 802.1q...

I have two (2) Cisco 2501 routersRtr A S1 - ip address 201.100.11.2E0 - ip address 192.5.5.1PC - attached to E0 - ip address 192.5.5.5 subnet mask 255.255.255.0 gateway 192.5.5.1Rtr BS0 - ip address 201.100.11....

If TOM telnets to a pc on a remote subnet/network, which MAC address will be present in thte ARP table when he issue the show arp command ?A. MAC address of the destination host Ethernet port B. MAC address of the local router Ethernet port C. MAC ad...