How to reset DSP on the 2600 and 3600 without reset the controller or reset the routers.
How to reset DSP on the 2600 and 3600 without reset the controller or reset the routers.
Hi all,I have a situation where I telnet to routerA. This router has, via its AUX port, a connection to routerB on the console-port.So I can normally do a reverse telnet from routerA to routerB. (via the lo0 on port 2001 on routerA)Problem is, router...
Hello,it act's about the CISCO WC210 WLAN Camera, I would be really happy, if somebody could help us to eliminate our problem InformatiomWe are using the WVC210 WLAN-Cameras (http://ww:w.cisco.com/en/US/products/ps9948/), this camera has a web serve...
Hello,Forgive me if I am posting to the wrong location. This is my first post.I am going to be updating the IOS on our Cisco ASA 5520 from verion 7.0(8) to 8.2(5). I am also going to setup AnyConnect. Are there any major changes in the 2 IOS versi...
Hi,I have two routers R1 and R2 with FastEthernet Interface IP address (F0/0)10.1.0.1 and (F0/0)10.1.0.2 respectively. I am using HSRP and R1 is active and R2 is in standby state. Whats happening is when I am applying ACLs in R1 on F0/0 I cannot teln...
This is probably a very silly question, but I am at a loss. Is the configuration information for each of the access points that has joined a wireless lan controller stored somewhere specifically in the configuration screens? I enabled the power i...
can anyone share a daily checklist file for monitoring Switches and Routers. we don not have any tools in place so need to monitor manually.
Hello,I've had a look through the Cisco documentation on trouble shooting issues at layer 1 on ATM but cannot find any that relate to my issue.I have a Cisco 857 that is unable to sync, the CD light just keeps constantly flashing. I got the router ba...
I am not an IT person. I am the Director of a library, and we are trying to install filter software at our main location and branches. The admin console has been installed at the main branch, but I need to allow access to ports 58000-58003 through ...
Hello everyone,Many pages describing EIGRP say that one of used metrics is the interface MTU. However, the formula for calculating the composite metric does not take MTU into account so the MTU can not affect the composite metric of a route.I would l...
Hi thereI have came up with a strange problem recently, maybe someone else experienced a similar problem and was successful in solving it?I have a LAN with Cisco 1941 as the only router with NAT that connects it to the internet, with a single public ...
So I'm trying to get a configuration going and im not sure its even possible. I have multiple vlans for internal networks. net 192net 10.0net 10.99 (the rest of the net statement really doesnt matter)External I have a pool of addresses from the isp. ...
I have configured WCCP on a 6509 switch to redirect the traffic to Websense transparently. Created an access-list and permit all the subnets which require inspection everything is working fine, but the issue is I denied some host's in ACL to be bypa...
On a router with Tunnel interface configured when I issue 'sho interface tunnel' command the MTU size shown is 1514, but when I issue 'sho ip interface tunnel' the MTU size is 1476. What is the actual MTU applicable to the interface.
Suppose a broadcasted IP packet reaches one of the integrated RJ-45 ports on a 2911 ISR G2, will it be possible to configure the router so that the other integrated RJ-45 ports, ESM/EHWIC modules installed on the router, as well as the MGF also recie...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
02-20-2024 07:45 AM | ||
02-15-2024 09:08 AM | ||
02-14-2024 04:00 AM | ||
11-10-2023 09:28 AM | ||
11-09-2023 09:30 AM |