Please I need to know what I will do my CCNP cert was expired.
Please I need to know what I will do my CCNP cert was expired.
Hi there.Resently i configure some MC20x20V cards with mac-domain 1/ 2 (one dw for tow upstreams) but the problem is when i whant see the dowsntream utilization in the snmpwalk only i see trafic in the interface downstream interface Cable6/1/0 (for e...
Hi, i cannot make my router to get the correct time from a ntp server.This is the output from the show ntp associations command192.168.100.65 configured, insane, invalid, stratum 2ref ID 192.168.100.94, time D164632D.40C3760B (17:05:33.252 CDT Thu A...
I have several Catalyst 3550 switches running IOS 12.1(14)EA1. I have observed thefollowing behavior:PC connected to port boots, works fine. Output from "show mac address-table interface f0/8" lists the MAC of the PC. If the PC is quiet on the net...
hi guys!l have my term server 2511 and l was tryng to recovery the password but at the rommon mode, l cannot have any access even when l do confreg 0x2142he brings me tho this: transaction "CONFREG' domaine server (172.16.15.30) (172.44.244.10) (17...
I have an 1811 configured with dhcp scope and generally it works correctly. I have a host on the vlan/subnet that the scope is assigned that can receive an IP and all the specifics from the dhcp server. See the pool below:ip dhcp pool 192.168.233.0/2...
Hi All,I have been searching for Visio Stencils for the following hardware:Cisco MCS 7800Ironport C370Ironport S370Any help in finding stencils for these would be greatly appreciated.
Hi, Need help regarding 1841 & 3845 router. We send 30 GB data on 100 Mbps link. First time we use 3845 router for sending the data and 47 Min are required to complete the data, during this link utilization was 100%. After that we send same data thro...
Hi AllHow do you reset a 1252ag access point that has the mode button disabled?Thanks
IP_ADDRESS: 10.10.10.1> IP_SUBNET_MASK: 255.255.255.0> DEFAULT_GATEWAY: 10.10.10.10> TFTP_SERVER: 10.10.10.10> TFTP_FILE: c2600-js-mz.122-15.T16.bin> ....> ARP: ADDRESS RESOLUTION for 10.10.10.10 timed out> ARP failed with failure code 1. TFTP trans...
We are getting "Deny IP due to land attack" messages on our ASA approximately every 5 minutes. I have done some diagnostic work and have found the "looping-address" record associated with this attack. From that it appear that the problem is happening...
Is it possible to create a site -to-site tunnel between a 6513 switch and a PIX ?How can i achive this?Is it a good idea to create tunnel between a COre switch and another site?
Does anyone know if you can remove items(devices) from My Added Devices (CCO - Support - Download Software - My Added Devices)?
Hello everyone,can anyone tell me how can i access the backup SUP from telnet/console while it's in the standby state?Regards,Sherief EL Hamalawy
I have set up an ACL on my 3750 switch to deny icmp from PC A on our inside network to PC B on a different VLAN on our inside network using the following ACLs:deny icmp host 10.1.17.15 host 10.3.10.4deny icmp host 10.3.10.4 host 10.1.17.15-- or --de...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM | ||
05-29-2024 04:52 AM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 | |
1 |