Can i manage bandwidth for a VLAN, I mean can i fix a Bandwidth on VLAN, e.g, If i apply 250Kbps for a VLAN 101 , evry client shared this bandwidth, if total customer in VLAN 100 is 10, each use 25Kbps bandwidth . Thank You.
Can i manage bandwidth for a VLAN, I mean can i fix a Bandwidth on VLAN, e.g, If i apply 250Kbps for a VLAN 101 , evry client shared this bandwidth, if total customer in VLAN 100 is 10, each use 25Kbps bandwidth . Thank You.
HiI'm about to go live with a new bgp setting. What I would like to know is if things go wrong what can I do to fall back to my original settings? IS it simply a case of putting a "no" in fron tof my config line and that will revert it back to its or...
Hi,I have switch 2900 series XL losing the password and the Mode Button not work. What i can do for this problem? Please give a solution.Wawan Kurniawan
I have configured on a Cat 3550 the following.interface FastEthernet0/48 description CAPI switchport access vlan 911 switchport trunk pruning vlan 2-1001,1006-4094 no ip address duplex full speed 100I am now trying to remove the line switchport trunk...
Can i manage bandwidth for a VLAN, I mean can i fix a Bandwidth on VLAN, e.g,If i apply 250Kbps for a VLAN 101 , evry client shared this bandwidth, if total customer in VLAN 100 is 10, each use 25Kbps bandwidth .Thank You.
Hi All,I know this topic has been covered earlier but nobody seems to of given a definitive answer.Almost all of the documentation I can see says that a switch in VTP Client Mode does not store any vlan info into it's NVRAM.My testing in the lab indi...
hi, there is option to specify default gateway on switch. what is the purpose of it?Regardsskrao
Hi, could any one tell me what does the following means? 1-spanning-tree mode pvst. 2-spanning-tree loopguard default. 3-no spanning-tree optimize bpdu transmission. 4-spanning-tree extend system-id.the above is written when I issue (sh run) on the S...
One user make network loop which connect the same hub with same cable. So there is many traffic and it make 4510R cpu utilization reach 90%-100%. There is about 20 trunks. After show interface, output rate of every trunk is about 500Mb/s.I think (500...
Pls let me know the Diff. B/W Cat IOS $ Integrated IOS.and Is there any reason why they named as catalyst switch.Thx in advance for a reply
Hi All, I've decided to go through CCIE certification, but I would like to know the following:- 1- Should I have to be CCNP/CCIP/CCDP or CCSP certified. 2- Could u show me helpfull links that could help. 3- What is the latest version (books) numbers ...
If I have 2 routers connected to my core and im running eigrp and the 2 other routers are advertising the same network, both the same speed links and delays etc, would they load balance or would eigrp pick on and use the other as backup, and if so Ho...
hi!our sites use all 3COM backbone and access switch.they use about 80 Macintosh pc.but , if use cisco 2950 switch instead of 3com switch , mac pc do not see another server ( another vlan)routing is good , but i think Layer 2 ' issue.thanks
I would like to creat a virtual trunk between two 2950, both are far from each other i mean many switches install between them, how can i creat a tunnel between or Virtual trunk port.
C3550-12G#wr mBuilding configuration...Error writing new config file "flash:/config.text.new"Error writing new config file "flash:/private-config.text.new"[OK]
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-17-2024 11:30 PM | ||
10-07-2024 07:08 AM | ||
09-26-2024 02:28 AM | ||
08-07-2024 06:15 AM | ||
07-17-2024 11:08 AM |
User | Count |
---|---|
2 | |
2 | |
1 | |
1 | |
1 |