Routers - Small Business

Hi i have my RV220 running 5 vpn site-site tunnels.192.168.1.0 --> 192.168.2.0   192.168.1.0 --> 192.168.3.0192.168.1.0 --> 192.168.4.0192.168.1.0 --> 192.168.5.0I connect to my 192.168.1.0 network with SSL VPN and PPTP VPN from my ipad so far so goo...

Buenos dias:Tenemos un problema  a la hora de redireccionar puertos. en concreto con el puerto de termial 3389Hemos creado 2 reglas o custon SERVICE1. TERMINAL Type TCP  Start port 3389 finifsh port 33892. Terminal 2  Type TCP SP 4444 FP 4444 En Port...

Hi,We have an CISCO 2951 as a central hub in an IPSec VPN community, with six WRVS4400N branch office routers connecting into it.Setting up the VPN tunnels worked fine, except after a while the tunnels seem to disconnect all by themselves, and they w...

Hello. I am wondering if someone can offer a sample config, or point me in the right direction. I an attempting to set up a site to site VPN between an ASA 5505 and a SR520. I have set up the 5505 with ASDM, but there is no site to site VPN config in...

Hello all,I'm using a SRP521W-U. I've set up a SIP account on Line 1.I would like to be able to answer incoming calls on both FXS1 and FXS2.How do I achieve that both ports will ring?Thanks.

I need to set up some security cameras here, and the boss has a never  used Cisco WAP4410N router collecting dust, and told me to install it. I gotta use my own personal laptop, it's a  small netbook, Aspire One DN55E using Windows 7 and Firefox. The...

I want to split my traffic between two ISP's.  I want all traffic to pass over one connection EXCEPT my VPN tunnels, which I want to use the second ISP.  How should I set up (protocol binding?) to accomplish this?  (I have run into various problems t...

I'm configuring a RV042 and have some questions;1) Do I understand correctly that PAT rules (created under uPnP) bypass the firewall rules? I need to filter some PAT connections on originating IP and that does not seem to be an option. I tried creati...

I am trying to add a couple VOIP phone units that do not have their own router.  They are designed to run of the existing router and have three ranges of UDP ports opened up.  They also do not advise using internal (private) statics on the phones.So ...

I have just purchased the RV042 and while it is working great on WAN1 over Xfinity/Comcast broadband, I'm unable to get it working with my AT&T DSL for WAN2.  I am planning on running this in failover mode - not load balancing.The DSL modem it is con...

I was running firmware 1.3.98-tm - and everything seemed to be working fine (no complaints from me - things ripped)Serial Number :      DEZ00610370xFirmware version :      1.3.98-tm (Jun 20 2008   18:37:29)CPU :    Intel IXP425-533Not sure if I have ...

I have configured a VPN tunnel between two remote locations using static IP addresses on two RV042 routers. The tunnel seems to work but the problem is that when the two hosts attempt to ping each other only one can successfully ping. One PC with IP ...

How can I report a bug so it is logged as a "CDETS case" (http://tools.cisco.com/Support/BugToolKit) and a engineer is actually looking at it?Device:----------PID VID : RV016 V03Firmware Version : v4.2.1.02 (Jan 18 2012 14:10:55)irmware MD5 Checksum ...