Hi, I am creating a network within packet tracer, but am having trouble understanding how I can make my OSPF network take the most optimum route.I have manually costed the Gigabit interfaces at 2, and serial interfaces at 100 using the ip ospf cost c...
Hello reference paper: https://www.cisco.com/c/dam/en/us/products/collateral/routers/3800-series-integrated-services-routers-isr/prod_white_paper0900aecd806f698a.pdf In my case I need to connect C2811/C2921 in Cross-Stack EtherChannel to a stack o...
We have couple l2tpv3 tunnels between C2911 and C1921.which, in turn, pass through a DMVPN tunnel through the provider cloud.And plain copy operation of a data, say ~100Mb and more in vlan 5 that xconnected lead to a high cpu load up to 100% on a C2...
Hello all,Please reference the image for convenience. R1 and R2 are our routers running ebgp with two isp R3 and R4 which are sending default routes towards us.R1 and R2 are ibgp peers also sending default route to each other also running vrrp.R5 is...
Hi there, Thanks for reading. I'm wondering what the upper limits as far as bandwidth for tunnel traffic on 800 series routers. Will they support a 50Mbps circuit connection? Thanks again, Bob
The L3 tunnel is up and works great. Now I'm testing it with my local ISP services and I'm trying to manage the remote ASA through the tunnel. I can ping/ssh from PC to PC through the tunnel (192.168.168.140 <-> 192.168.180.4) but I can't ping/ssh ...
Hello all. I was wondering if you ca help. I am trying to run a capture on our WAN interface for a certain IP. Every time I try to execute the command I receive "EPC configuration not permitted on standby" ROPS-M0-A2-2-4500X-VSS#monitor capture MYC...
Im building an ASR 1001X, and I see so many versions of software !! Denali 16.3.5 (MD), vs Everest 16.6.2(ED), vs Fuji 16.7.1 (ED) .. Anyone knows what the difference is ? and which is the stable version that I should go with ? I couldnt find any c...
Hi all, I have a pair of 4400s setup specifically for SIP voice services. In our config we have an 'outside' public IP connecting to the carrier voice cloud, and a 'inside' IP connecting to my private IP network. Since i have two 4400s we wanted to...
Hello to the community. I have this topology: The green devices are switches layer 2, the blue devices are switches layer 3. I use the VLAN250 as transit network, the green devices has only the vlan250 (L2) permitted on every trunk: SWT-A: rou...
Hello, I have upgraded route reflector in private MPLS network from IOS XE 3.16.5 to Everest 16.6.5 release. After upgrade, dynamic BGP peers did not connect to RR. In debug, I see mesaages such as: 004668: Mar 10 02:07:02.382 MET: BGP:DN: peer-gro...
Hello, Does anyone know if IOSXR on ASR9K supports SNMP counters for BGP flowspec announces ? All I want to do is to retrieve the counters using SNMP. cf: RP/0/RSP0/CPU0:XXX#show flowspec afi-all detail Wed Mar 6 10:55:53.481 CET AFI: IPv4 Flow ...
Hi there. I am trying to configure a DMVPN overlay and want to create multiple VRFs in this overlay. On the hub router are all the tunnels terminated on the same interface in Global Routing but with different network-ids. But when I try and get...
Hi any one can help ne to know what is this error at the Log and if it will impact the service Mar 4 10:59:03.138: %SIGNATURE-3-NOT_ABLE_TO_PROCESS: %ERROR: Not able to process Signature in disk2:!P!N@pA55. Mar 4 12:09:38.470: %SIGNATURE-3-...
Hello - It is a general question to know how to determine the model of the Router based on the WAN Internet link i am going to connect. Reading the article http://www.anticisco.ru/pubs/ISR_G2_Perfomance.pdf and other datasheet it is mentioned about ...
