Dear Community,I have I lab setup as attached where R10-R3-R4-R5-R6-R11BGP routes for R6 routes appear in the routing table of R3 and vice-versa. R5 does the route redistribution between BGP 65200 and EIGRP 100 and vice versa. However, when I try to ...
Forum Posts
Hi All, I am looking for advice on how to configure / physically deploy an active/passive fw configuration when the ISP are providing a HSRP virtual IP for MPLS connectivity.The same ISP provides 2 routers and a managed virtual HSRP IP. I was intendi...
I'm an MSP what is managing a Cisco ASA firewall in a datacenter - Software Version 9.16(4)14The ISP connection is 500MB down/100 MB upWe have about 20 IPSec VPN tunnels & 50 RAS VPN's at any given time on this firewall with a mixture of IKEv1 & IKEv...
Hello Everyone, I was in the process of backing up a 2911 router. after sucefully backing up the startup configuration, i accidentally deleted the "IOS image" from the flash0 : memory. now the router is in rommon1> mode, how can i reset or reload my ...
My cisco packet tracer came with a black default workspace. I've tried changing it to white without success. This workspace is not making me see the coordination well. Please help me. I can't work with this black screen
I am creating an EVE-NG lab environment for cisco SDWAN deployment. Routing is complete from controllers to cEdge Aggregation routers and towards Branch routers. After configuring SDWAN tunnel configurations i have observed that cotrol connections ar...
Hi guys, I have the following connection between the router and the firewall:The routes are being received from the BGP peer but are not in the routing table.Follows the Cisco config:Does anyone have any idea what the problem is?
Hello,We have cisco Router C1111-4PLTEEA with c1100-universalk9.16.12.04.SPA.bin installed firmware. Also we have Site2Site VPN with our HQ. CCTV traffic from this router is going to HQ via vpn, but during this process we have a lot of packet loss is...
Hi everyone,I encountered a strange situation and could use some insights. Initially, I had the following setup:- **Interface**: VLAN 200- **Static IP Address**: 172.16.16.12- **Static Route**:```ip route 0.0.0.0 0.0.0.0 172.16.16.245```Running `show...
Hi all,hope you can help me.I'm having my mind melted with the Keychain Accept and Lifetimes, basically I'm getting confused from all the info I see. Please would it be possible to confirm if the below is correct? key chain TESTkey 6accept-lifetime l...
We are trying to connect two links on a router using two autonomous systems simultaneously, but we can only get one connection to work and not both at the same time. Does anyone know if a license is needed to support multiple AS systems? If so, what ...
This post maybe could go to switching, but as the problem is a C1111 router I figure to post it here. I have 2x of these routers at 2 different locations that connect via a fiber network. I am told the switch connecting is "untagged". I have 3 vlans ...
Virtual machines will be moved from on-premises virtual machines to Azure.Since on-premises ARP in Azure environment cannot be learned, the following actions are requiredSince clouds do not support Address Resolution Protocol (ARP), and the cloud inf...
We have a client running RIP between 2 sites over 2 links, 1 link is DMVPN and the other is Site-to-Site VPN. now the way their RIP is setup is that they have static routes to the main line which is the DMVPN that are redistributed to RIP. now they a...
Hi, I have two routers having BGP peer with each other. Both are working fine.I want to configure Soft-Inbound in BGP configuration on both end. I want to double confirm, if I will activate neibhor x.x.x.x soft-inbound command under BGP, then my BGP ...
