Hi All,As I'm doing an EIGRP lab, I noticed a strange behavior with the 'variance' command. Its very possible that I'm missing something, which is why I wanted to ask here so if someone can point out the cause of this behavior or if otherwise the doc...
Forum Posts
Resolved! BGP not advertising connected routes
Hello,I have a CE router (ACME2) connected to an MPLS network connected via a PE router (PE-2).The probem is: ACME2 router is not advertising connected route 192.168.50.0 to the PE router (PE-2) ACME2: ACME2#show ip bgp neighbors 192.168.5.1 advertis...
I am in need of the heat output of the 4431 router NON-PoE and am not able to find this in the product data sheet. Understand the environment specs but need to device BTU output for HVAC planning in the data center, Thanks Scott
Resolved! ACL issue
Hi friends, I am facing a strange issue in ACL. we have many Cisco 4500 series VSS pair in all our branch offices acting as a core. we have below kind of ACL. Extended IP access list 10110 permit udp any eq bootpc host 255.255.255.255 eq bootps (14...
Hello, Let me start by telling I'm a complete beginner, but I've tried reading posts on this forum, YouTube, Googling etc. to find an solution, but I'm stuck. I have an static IP from my ISP, it's a /30 subnet, so I only have one IP for my WAN and a ...
Hi, I'm trying to configure following scenarioRouter: 3825 (with 2 ports)Two ISP with different network addressOne DHCP I terminated the ISP's in my 3750G switch on different vlans, made a trunk and connected it to router. Then I made access port i...
Device and OS Info :c2960x-universalk9-mz.152-2.E6.bin On this switch I have a port which is always in amber color and never get green. I have checked and changed the cables but that didn't helped. Interface if gigabit and running on full duplex.Howe...
Hi, I’m looking for some help on an EIGRP issue we’re having with route advertisements over a FlexVPN between two sites. The spoke router is receiving a full routing table from the hub and this is being redistributed down to the L3 Switch but the h...
Resolved! Extended ACL problems blocking icmp.
hey guys i am having trouble with extended ACLs R1 and R2 they keep blocking icmp echo reply. i want to allow pc-a and PC-B to receive ping replies but deny icmp traffic from coming in to both R1 and R2 here are my access list.access-list 101 permi...
Hello,I have autonegotiation disable on my interfcae what should be duplex setting on other end?Router#sh run int Gi0/3/0Building configuration...Current configuration : 334 bytes!interface GigabitEthernet0/3/0dampeningbandwidth 1000000no ip addressn...
My apologies if this is in the wrong community. I'm studying for the 200-105 exam, passed the 100-105 last month. I've got a small lab network setup with 3 x 2811s and 3 x 3560s. I've gotten pretty good with them and enjoy playing around and makin...
Resolved! need help with extended ACLs
hello i need help with extended acls. here is the thing i want to make pc a and b be able to ping outside and receive replies. but at the the same time i want to deny icmp traffic from coming into R1 and R2. what about implicit deny will that affect ...
Hello Guys, I need your help. I've got a Cisco 892 Router in which I'm trying to configure PPPoE connection. I'm not a pro, I've tried commands which I founded on the internet but it didn't work. I've reset the router. Please help me out. Thanks.
Resolved! Wireshark Issue With GNS3
Hi whenever i refresh or stop&start live captures im getting below error Please help anyone on this wireshark issue with GNS3 please find the attached photo Thanks in advance.
I just got to using this router that I want to use for practising the CCNA course and it seems to be bricked...Tried the usual things like a "hard reset", trying default IP addresses I purchased this cable to access the console port (of which I dow...
